Dead Air Nomad Ti XC

[pods8 (Rugged Stitching)]

Nope. I kind of wondered about that though.

Probably a gray area and my FFL was being conservative.

 

[HighUintas]

After attempting to remove the direct thread hub on my nomad and nearly pulling a muscle..... I think maybe I'll just leave it in factory config. I'm feeling a little too lazy and cheap to mess with it haha

 

[HighUintas]

I tested mine out for the first time today on my 16" 223. I shot 1 shot with the scythe and 1 with the nomad without hearing protection and couldn't tell a difference. Maybe more testing is needed, but I don't care much. Scythe is plenty quiet and I'm sure this is quieter.... And stronger.

 

[ScreamingPotato]

Bauer is doing free tax stamps through end of today and have most of the Nomad flavors in stock.

 

[Qholum37]

Bauer is doing free tax stamps through end of today and have most of the Nomad flavors in stock.

Do you need a code? Didn’t see any mention of that when I went to the site

 

[ScreamingPotato]

Do you need a code? Didn’t see any mention of that when I went to the site

taxseason

Sorry I thought it was on their website.

 

[ScreamingPotato]

Thought this could be useful for somebody seeing this thread. The DA DT hub is a bit heavy. I replaced it with an ultralight from C&S in Colorado Springs. Saved about 1/2 without the wrench flat too, hopefully that doesn't bite me later. Might add some anti seize but don't really plan on removing it anyway.

 

[HighUintas]

Thought this could be useful for somebody seeing this thread. The DA DT hub is a bit heavy. I replaced it with an ultralight from C&S in Colorado Springs. Saved about 1/2 without the wrench flat too, hopefully that doesn't bite me later. Might add some anti seize but don't really plan on removing it anyway.

How do you torque that c&s on without wrench flats?

 

[ScreamingPotato]

How do you torque that c&s on without wrench flats?

It's got spanner wrench holes.

 

[Ratzc1257]

Does anyone run a ab raptor 8 on an ar platform?

 

[ChrisAU]

Thought this could be useful for somebody seeing this thread. The DA DT hub is a bit heavy. I replaced it with an ultralight from C&S in Colorado Springs. Saved about 1/2 without the wrench flat too, hopefully that doesn't bite me later. Might add some anti seize but don't really plan on removing it anyway.

Link to that adapter? Google isn’t helping me

 

[ScreamingPotato]

Link to that adapter? Google isn’t helping me

You have to tell him to take out more metal because you want it as light as possible. Tell him what you want and he'll make it for you. He made an m15x1 for my goofy Tikka thread pattern.

Suppressor Adapters

Custom suppressor adapter solutions We specialize in making custom suppressor adapters from: Standard Bravo, Alpha, Charlie pattern in inch or metric thread, RH and LH We also offer custom jobs wit…

candsarmory.com

 

[HighUintas]

You have to tell him to take out more metal because you want it as light as possible. Tell him what you want and he'll make it for you. He made an m15x1 for my goofy Tikka thread pattern.

Suppressor Adapters

Custom suppressor adapter solutions We specialize in making custom suppressor adapters from: Standard Bravo, Alpha, Charlie pattern in inch or metric thread, RH and LH We also offer custom jobs wit…

candsarmory.com

That is awesome. So yours is nearly the same as using a sico scythe flush DT, right? It looks like you might only have 1/8" or less of extra length

 

[ScreamingPotato]

That is awesome. So yours is nearly the same as using a sico scythe flush DT, right? It looks like you might only have 1/8" or less of extra length

There's almost no extra length, that flat spot is tiny maybe 1/16" if I'm guessing but I can measure after work tomorrow. It saves at least 3/8" over the factory Nomad DT hub, maybe 1/2".
If y'all are ordering from that dude you may tell him you're from Rokslide and see if he wants to sponsor and offer discounts. He was curious how I found him.
Edit: Tell him I want my discount as a credit on my next order lol.