Silencerco Scythe TI review

[Grundy53]

Get some of this. It will last you a lifetime.

And no matter how careful you are, you will end up with it all over you...

Sent from my SM-S901U using Tapatalk

 

[kswaterfowl]

And no matter how careful you are, you will end up with it all over you...

Sent from my SM-S901U using Tapatalk

You are not kidding. Look like the tin man when you're done.

 

[Pickettpuncher]

Picked up my scythe on Monday, and finally got around to shooting it this evening. Highly impressed. Couple things I did notice. Pressure changed considerably. I’ve been 4 grains higher and had less bolt resistance than I did tonight, but primers looked just fine. Once I adjusted the scope, my grouping was fine. I would expect some change in the pressure, but wondering others experiences. I would have chronoed but I doubt my Magnetospeed would read it. 20” preferred barrel, 25cm, h4350 41.5gr, 134 eldm, 2630fps before the suppressor.

 

[left hunter]

Seeing as it’s July, what was the temp when you did the original test before the suppressor came and compared to today?

 

[Pickettpuncher]

Seeing as it’s July, what was the temp when you did the original test before the suppressor came and compared to today?

I shot a month ago and was approximately the same temp, with no issue

 

[Pickettpuncher]

Seeing as it’s July, what was the temp when you did the original test before the suppressor came and compared to today?

And here’s a 12-15 round group without suppressor

 

[Marshfly]

I don't see any on SilencerCo's website. Either way, I am going to stick some copper based anti seize on my threads

Maybe I got it from Griffin. That’s my other suppressor.

 

[bhylton]

I shot a month ago and was approximately the same temp, with no issue

I have heavy ejector swipe with my scythe that is not present unsuppressed as well

 

[5811]

https://www.bauer-precision.com/silencerco-scythe-ti-7-62mm-black/

Bauer Precision has these in stock, 15% off with discount code chickenstrips.

 

[Pickettpuncher]

I have heavy ejector swipe with my scythe that is not present unsuppressed as well

Do you have heavy bolt with the swipe.

 

[WKR]

Picked up my scythe on Monday, and finally got around to shooting it this evening. Highly impressed. Couple things I did notice. Pressure changed considerably. I’ve been 4 grains higher and had less bolt resistance than I did tonight, but primers looked just fine. Once I adjusted the scope, my grouping was fine. I would expect some change in the pressure, but wondering others experiences. I would have chronoed but I doubt my Magnetospeed would read it. 20” preferred barrel, 25cm, h4350 41.5gr, 134 eldm, 2630fps before the suppressor. View attachment 744762View attachment 744763

4 grains or 4 tenths of a grain?
I'm trying to figure out how you fit 45.5 grains of h4350 in 25 creed alpha brass

Also curious which primer that is in the picture? Fed?

 

[WKR]

I've had one of the Scythe's in jail since January 31st along with 3 others...I never saw the fast form 4 approvals that seems like everyone else is seeing. At this point I'm expecting my ffl 07 and sot applications and licenses to be approved before my form 4's

 

[Pickettpuncher]

4 grains or 4 tenths of a grain?
I'm trying to figure out how you fit 45.5 grains of h4350 in 25 creed alpha brass

Also curious which primer that is in the picture? Fed?

During load development I stopped at 45 grains of h4350. The primer is a fed small rifle match.

 

[WKR]

During load development I stopped at 45 grains of h4350. The primer is a fed small rifle match.

I start getting compressed at around 42-43 grains

Do you notice the cratered primers? I use the same fed primers and they seem soft. Even at low pressure.

 

[Pickettpuncher]

I start getting compressed at around 42-43 grains

Do you notice the cratered primers? I use the same fed primers and they seem soft. Even at low pressure.

I personally don’t worry about cratered primers. I do pay some attention to the primer edge. The hard bolt lift is what caught my attention. I did get some ejector marks closer to 44-45 grains. I didn’t worry too much since the bolt lift was fine and primers were fine. I dropped to 41.5 as that’s where my rifle shot the best, just a bit on the slow side. I’ll send you a pm as I don’t wanna clutter this thread


To be clear, I expected some variation in current load with and without, I just didn’t expect that much variation.

 

[Skerhunter]

Anyone running one of these on an AR? How’s the back pressure?

Works great on mine don’t notice a difference between my gas vs bolt guns in 224 (shooters perspective).

 

[bhylton]

Do you have heavy bolt with the swipe.

Maybe a little heavier. But def ejector swipe.

 

[Stache Attack]

I’ve been shooting with mine aswell, after a few shots and in full sun I got some pressure signs but was running pressure signs.

I’m impressed aswell might drop .5 off my load but don’t really want too

 

[Reburn]

Get some of this. It will last you a lifetime.

Man yall are anti seizing everything and I am doing the opposite. I have put a small drop of rockset on the direct thread end and the muzzle brake end. I have had both come loose and change POI with long strings of fire.

 

[ReaptheHeat]

Ive been on backorder for the non-black version since April on SilencerShop.. anyone having luck? GF got the black version done and cleared in 2 weeks...