Savage 110 ultralight (proof barrel)

[Gear-Reviewer]

Hmmm 280 AI shooting 162-168’s or 6.5 prc shooting 156’s...

 

[CORidgeRunner]

"Low stock" for the 280 AI here:

Savage 110 Ultralite .280 Ackley Improved, 22" PROOF Research Barrel, AccuFit, 4rd

Savage 110 Ultralite .280 Ackley Improved, 22" PROOF Research Barrel, AccuFit, 4rd. Savage Arms 57579. Savage teamed up with PROOF Research once again to craft a barrel specific for a purpose driven firearm. At 6 pounds and under, the 110 Ultralite is designed to combat elevation and elements whi...

www.impactguns.com

I did buy my Ultralite 6.5 PRC from them. No issues other than the wait.

I just ordered a 110 ultralight in .280ai from them yesterday. Thanks for posting, I was having hell finding one in .280.

 

[CORidgeRunner]

Here is my first 5 shot group out of my .280 AI. Running a YHM Resonator suppressor. That is with factory Hornady 162 grain ELD-X loads.
View attachment 181264

What base and scope rings did you end up going with. I ordered a 110 ultralight in .280 ai yesterday and should be here in a week or so. I need to get a base and rings ordered.

 

[gleason51]

What base and scope rings did you end up going with. I ordered a 110 ultralight in .280 ai yesterday and should be here in a week or so. I need to get a base and rings ordered.

I went with the EGW 0 MOA HD base and Warne mountain tech rings. The EGW HD series is already drilled for the #8 screws. Really happy with the set up.

 

[AZ_Hunter_2000]

I was able to see my PRC today. She's looking pretty good. The 142 gr ABLR, 143 gr ELD-X, and 147 gr ELD-M show a lot of promise. Representative 3-shot group is included in an attached photo (1/4" grid). The 156 gr Bergers did not do as well in comparison. My friend will be making some adjustments to see what he can do to get the Bergers to group.

I do wish the bolt action was smoother like the 110 (Tikka smooth would have been asking for too much) as this one is a bit "rough". Hoping it smooths out over time and use. With that said, no issues getting rounds chambered and sending bullets down range.

I am looking forward to seeing the finished package.

 

[kylejason79]

Hey guys - I just ordered a 110 Ultralight in 6.5 Creedmoor and would like to get a muzzle brake contoured to fit the barrel. Can anyone tell me what the outer diameter is at the base of this rifle's muzzle brake threading? The Proof Research website says 0.963 inches but when I called to confirm they weren't very helpful. Thanks in advance.

 

[AZ_Hunter_2000]

Mine is away getting loads developed for it. However, Savage's site says "Threaded muzzle for 5/8 24 with flush fit cap".

 

[kylejason79]

Thanks - I was just trying to figure out the diameter of that "flush fit cap" so that the contour of the muzzle brake seamlessly fits the diameter of the barrel. I appreciate the help though.

 

[505Wapiti]

Thanks - I was just trying to figure out the diameter of that "flush fit cap" so that the contour of the muzzle brake seamlessly fits the diameter of the barrel. I appreciate the help though.

I am in the same boat. I bought an electronic caliper yesterday to measure and have not gotten around to it. I will post measurement hopefully later tonight.

 

[Fshnpole]

I am in the same boat. I bought an electronic caliper yesterday to measure and have not gotten around to it. I will post measurement hopefully later tonight.

.750 in is what I had mine milled down to, fit flush

 

[505Wapiti]

.750 in is what I had mine milled down to, fit flush

Bingo... .7450 is what I’m gettin on my cheap calipers. What brake are you using if you don’t mind me asking? I’ve never bought a production brake as a local gunsmith here makes his own and is the only one I’ve ever used. I am considering the APA Gen 3 with tunable top ports. Anyone have experience with them?

 

[Fshnpole]

Bingo... .7450 is what I’m gettin on my cheap calipers. What brake are you using if you don’t mind me asking? I’ve never bought a production brake as a local gunsmith here makes his own and is the only one I’ve ever used. I am considering the APA Gen 3 with tunable top ports. Anyone have experience with them?

I bought one from Ross Schuler

Ross muzzle brakes

 

[kylejason79]

Thanks for the info - I think I'm gonna go with a Northwest Precision muzzle brake.

 

[NMhunter92]

Guys does this look right?

EGW Round back short action 0 MOA
.300wsm

 

[Savagenut]

Yep. Looks good

 

[Chad miller]

Has anyone taken the stock off and seen what they weigh?

 

[twrob18]

I just got one in 280 AI and my stock weighs 1.83 lbs. The total weight of the rifle is 5.90 lbs on my scale.

 

[505Wapiti]

Making progress, finally got scope mounted but still waffling on brake choice. NF SHV 4-14x56 c522 mounted in Leupold Back country cross slot low rings on a Leopold Mark 4 20moa base. Thought I’d share a pic below, now I just need a little range time .

 

[Eddyzima]

Making progress, finally got scope mounted but still waffling on brake choice. NF SHV 4-14x56 c522 mounted in Leupold Back country cross slot low rings on a Leopold Mark 4 20moa base. Thought I’d share a pic below, now I just need a little range time .

View attachment 188077

Very nice! Now get it to the range and give us a report!

 

[NMhunter92]

Headed out today! Nice set up 505