Ultralight Ultralight Rifles

[PsRpOiGrRiAtM]

I have a 2-7 Burris Fullfield II that weighs 12oz with ballistic plex reticle.

I have the version of that with the E1 reticle and it's sitting on top of my 9.3x62 right now, but I haven't shot it on there yet.

 

[Thegman]

I’m one of those guys who has an iPhone tied to my work so I’ve never been able to get Strelock to work. Could you look at the 87gr v max going 2600 and 2640 and see how power lines up?

According to Strelock (should be pretty good ballpark):
At 2,600, 1.7" high @ 100Y and 7.5x lines you up pretty well out to at least 450Y


At 2640, 1.6" high @ 100Y and 8x lines up out as far (just squeaks by as 8x is about as far as I think that scope is easily usable)

 

[ezwy]

Thanks for that. I'll bump it up to 1.6-1.7 high at 100 and verify at range. since the reticle has the yardage numbers in it, it makes sense to use them.

According to Strelock (should be pretty good ballpark)

At 2,600, 1.7" high @ 100Y and 7.5x lines you up pretty well out to at least 450Y

 

[C Bow]

I put a lepould 2.5 x 8 on mine

 

[4090Sharps]

Got a nice Coues buck with my .223 ULUL at 400 yards. I was holding for the neck/shoulder juncture in hopes of an immediate drop, as most of the exit options for this buck were going to make for a painful and lengthy recovery. Shot landed a little right onto the neck, so it worked out. Recovered the bullet in the offside skin, then forgot it on a rock next to my pack



The terrain was pretty steep and rocky, and I packed my camp back a ways carrying water, so I was glad to have the light rifle for this hunt.

 

[Thegman]

Awesome! Great buck. I think you have the range-on-game record now for an UL-U,... time for @Taudisio to get busy with his 6x45.

What bullet/velocity/optics were you shooting?

 

[4090Sharps]

Awesome! Great buck. I think you have the range-on-game record now for an UL-U,... time for @Taudisio to get busy with his 6x45.

What bullet/velocity/optics were you shooting?

Thank you!

77 TMK, 2750 fps MV, 5x PA Microprism with Mil reticle.

I found the Microprism a little lacking for brightness and magnification in lower light during my hunt. The early evening shadows and the gray deer had me holding off on taking a 350 yard shot the evening prior. I could see well enough, but not as well as I would prefer for a confident shot or have experienced with conventional scopes.

 

[goalie]

Thank you!

77 TMK, 2750 fps MV, 5x PA Microprism with Mil reticle.

I found the Microprism a little lacking for brightness and magnification in lower light during my hunt. The early evening shadows and the gray deer had me holding off on taking a 350 yard shot the evening prior. I could see well enough, but not as well as I would prefer for a confident shot or have experienced with conventional scopes.

Yeah, I love my 3x micro prism but my "long" shots where I hunt with that are under 100 yards.

If over 200 was expected, I have other light scopes with more magnification I'd use.

 

[Taudisio]

View attachment 977907

Got a nice Coues buck with my .223 ULUL at 400 yards. I was holding for the neck/shoulder juncture in hopes of an immediate drop, as most of the exit options for this buck were going to make for a painful and lengthy recovery. Shot landed a little right onto the neck, so it worked out. Recovered the bullet in the offside skin, then forgot it on a rock next to my pack

View attachment 977908

The terrain was pretty steep and rocky, and I packed my camp back a ways carrying water, so I was glad to have the light rifle for this hunt.

Beautiful coues deer and nice shot!

Awesome! Great buck. I think you have the range-on-game record now for an UL-U,... time for @Taudisio to get busy with his 6x45.

What bullet/velocity/optics were you shooting?

Make it be deer season again and I’ll see what I can do.

 

[Zackw]

Afternoon everyone, so I've started to build out a ulul based on a bca side charger. I honestly don't have time to read through all 200 pages, so I was hoping that someone could give me a real quick answer. I'm trying to determine if it's worth the time & effort to build a carbon fiber handguard, or just order the jag composites. I've got a workshop and could build one out if it's a viable option. And if building one is the answer, what barrel nut is everyone using? Thanks for any info.

 

[Thegman]

Afternoon everyone, so I've started to build out a ulul based on a bca side charger. I honestly don't have time to read through all 200 pages, so I was hoping that someone could give me a real quick answer. I'm trying to determine if it's worth the time & effort to build a carbon fiber handguard, or just order the jag composites. I've got a workshop and could build one out if it's a viable option. And if building one is the answer, what barrel nut is everyone using? Thanks for any info.

It sounds like time is limited, so you may better off going with the Jag.

There are as many ways to build a CF handguard as there are handguards on this thread. I'm not sure if anyone is using the same stuff or approaching it the same way. I know mine is different than all the others.

It's actually very easy to build one similar to mine; it's the parts research and fitting that takes time. Mine are built with a barrel nut which isn't available currently, so not much help there. The rest is finding the right CF tubing and CF Seatpost clamp off e-bay.

There are aluminum barrel nuts on e-bay that will work with the type I make, or drill and screw CF tubing to the barrel nut like the Kaw Valley/Jag as they're also threaded. They're 34.4mm diameter so probably require fitting a 35mm ID / 37mm OD CF tube to fit.

E-bay barrel nut


If absolute weight isn't an issue, the Kaw Valley PCC is also a very good handguard, pretty lightweight and a lot cheaper than the Jag.

 

[4090Sharps]

Awesome! Great buck. I think you have the range-on-game record now for an UL-U,... time for @Taudisio to get busy with his 6x45.

What bullet/velocity/optics were you shooting?

If it's the record, I had better be exact 416 yards.

 

[Thegman]

If it's the record, I had better be exact 416 yards.

Shatters the previous record by 66 yards!

I did just find an 80 ELD-M load that, so far, seems to shoot really well in my $50 BCA pencil barrel (several loads seemed pretty good, one seemed really good, we'll see if that's consistent).

This past moose season I spotted a bull twice at about 450 yards. Both times tried to get closer and couldn't find him down in the trees. (I've never had to shoot a moose at much over 100 yards, if that). Was just thinking today that if I see a bull in the same spots next year...well...maybe...??

 

[ezwy]

Afternoon everyone, so I've started to build out a ulul based on a bca side charger. I honestly don't have time to read through all 200 pages, so I was hoping that someone could give me a real quick answer. I'm trying to determine if it's worth the time & effort to build a carbon fiber handguard, or just order the jag composites. I've got a workshop and could build one out if it's a viable option. And if building one is the answer, what barrel nut is everyone using? Thanks for any info.

I have used 3 different barrel nuts. Get a barrel nut first. The solo is about the lightest, but shorter than some. Measure the OD of nut. Order carbon tube off amazon with the same inside diameter. Drill and tap some holes for 8 or 10 mm hex head screws.
My solo barrel nut took a 35mm ID tube. Law valley nut a friend used was 38 ID. Have done two screws and four. Four “feels more secure” but haven’t had durability or accuracy issues with either.

 

[Welldone]

Got out today and hiked about 4 miles looking for hog sign ( hair on the barbed wire) and rooted up swamp bottoms.
300BLK
Fiochi 125 grain SST

 

[packgoatguy]

Afternoon everyone, so I've started to build out a ulul based on a bca side charger. I honestly don't have time to read through all 200 pages, so I was hoping that someone could give me a real quick answer. I'm trying to determine if it's worth the time & effort to build a carbon fiber handguard, or just order the jag composites. I've got a workshop and could build one out if it's a viable option. And if building one is the answer, what barrel nut is everyone using? Thanks for any info.

I use the JAG barrel nut, and an Amazon Carbon tube

Here is the post from this spring with weights

Post in thread 'Ultralight Ultralight Rifles' https://rokslide.com/forums/threads/ultralight-ultralight-rifles.329402/post-4105782

And I'll add, it's possible to over-tighten the barrel nut... I'd keep it at 30ft lbs, and use a quality torque wrench. Using an action rod is also a big part of the equation imo, to avoid unnecessary stress on other parts of the equation. And I think it helps to use some anti-sease on the threads, and tighten it to torque, then back it off, then repeat a few times.

 

[Gettincloser]

Any of you have a recommendation for a carbon fiber guard with a small arca adaptor? Factory or DIY? (Clearly wanting to keep the weight down but willing to accept the penalty.)

I have gotten spoiled to shooting off a tripod!

 

[doverpack12]

Any of you have a recommendation for a carbon fiber guard with a small arca adaptor? Factory or DIY? (Clearly wanting to keep the weight down but willing to accept the penalty.)

I have gotten spoiled to shooting off a tripod!

I drilled a couple holes in the Kaw Valley PCC and put a Spartan bipod adapter on using m-lok. The nuts tightened down nice

 

[180ls1]

the Weiser sparrow (for binoculars) may also be worth a look. Let’s you use your trekking pole as well for stability.

 

[packgoatguy]

Any of you have a recommendation for a carbon fiber guard with a small arca adaptor? Factory or DIY? (Clearly wanting to keep the weight down but willing to accept the penalty.)

I have gotten spoiled to shooting off a tripod!

DIY all the way. Cut a piece off of an aluminum arca rail, then make a spacer (3D Printer works great) then rough up the surface of both pieces and the carbon tube, then JB weld it together with original cold weld formula. Mine has held together for at least 300 rounds and is still going strong. Or you could 3D Print the whole arca piece (I've made a ring that goes around the carbon tube with the arca piece built it, and it worked well).