Tikka 223 magazine feeding issues

[ElPollo]

To this day my biggest issue is now cases hanging up on the case mouth when entering the chamber. Happens with all factory ammo a small chamfer on the chamber would entirely solve this. For now a small case mouth chamfer is the solution. Does anyone have a photo of a factory tikka chamber?

I was having this happen occasionally with factory mags and regularly with single feeds dropped in from the top on the factory mags. My expensive Waters mags resolved these issues. Take home is that I would be cautious on opening up the ramp or chamber because I don’t think that is ultimately the reason for the issue.

 

[Chris_in_Idaho]

So far I haven’t had any issues with rounds from the magazine failing to chamber (assuming the bolt picks them up), but if I try to drop a single round in through the ejection port it 100% gets stuck nose against the breech face.

 

[Formidilosus]

So far I haven’t had any issues with rounds from the magazine failing to chamber (assuming the bolt picks them up), but if I try to drop a single round in through the ejection port it 100% gets stuck nose against the breech face.

Have you stretched the magazine spring?

 

[rbutcher1234]

Stretch the mag spring, start paying more attention to mags after a season or two of use, and just be prepared to replace as needed. Mags get damaged being dropped, used, and abused. Just part of it.

FWIW, I had way more feeding issues with 223 aics accurate mags than factory tikka mags, so I pulled my 223 out of a bravo stock and back into the factory stock because of it.

 

[Chris_in_Idaho]

Have you stretched the magazine spring?

Not yet, I think the previous issue I had was probably because of the gummy sizing lube on the cases as you had pointed out. Thanks for that.

This reply about the rounds nosing against the face of the barrel when I drop them in through the ejection port I would think is unrelated to the magazine. But I could definitely be wrong.

I wasn't really trying to call that a problem, just adding a data point to the issue Stocky and ElPollo were discussing. I should have quoted.

 

[Formidilosus]

This reply about the rounds nosing against the face of the barrel when I drop them in through the ejection port I would think is unrelated to the magazine. But I could definitely be wrong.

I wasn't really trying to call that a problem, just adding a data point to the issue Stocky and ElPollo were discussing. I should have quoted.

Oh that’s a problem. You should absolutely be able to drop a round in the chamber and it feed. It’s usually because the front of the follower isn’t up all the way. Is it a factory stock and bottom metal?


The Tikka 223 mags seemed to start having issues about two years ago. Not sure what happened, and it’s not all of them-but it’s happening often enough that I’ve seen it with quite a few. The 4 rounders are better than the 6 rounders overall. I still have 2-3 original mags from 2013 or so that feed perfectly, but about 30-50% of new mags seemed to need to be tweaked. A lot, or most issues seem to be with non factory stocks and bottom metal- quite a few of the guns/mags that i have seen give issues, worked fine when everything was put back to factory.

 

[PaulDogs]

Oh that’s a problem. You should absolutely be able to drop a round in the chamber and it feed. It’s usually because the front of the follower isn’t up all the way. Is it a factory stock and bottom metal?


The Tikka 223 mags seemed to start having issues about two years ago. Not sure what happened, and it’s not all of them-but it’s happening often enough that I’ve seen it with quite a few. The 4 rounders are better than the 6 rounders overall. I still have 2-3 original mags from 2013 or so that feed perfectly, but about 30-50% of new mags seemed to need to be tweaked. A lot, or most issues seem to be with non factory stocks and bottom metal- quite a few of the guns/mags that i have seen give issues, worked fine when everything was put back to factory.

Any updates on extended use with the mambamags?


Sent from my iPhone using Tapatalk

 

[Formidilosus]

Any updates on extended use with the mambamags?


Sent from my iPhone using Tapatalk

Not a whole lot of rounds (relatively) but the one I have is feeding fantastically.