Show your Tikka ten round groups

Duh

WKR
Joined
Apr 5, 2023
Messages
619
Here’s my tikka 22-250 1:8 factory barrel and two 10 round groups this morning. Both groups were shot fairly rapid with no breaks between.

Haven’t found too much data on this combo so here’s mine: staball was a charge weight of 37.8 grains and the Varget was 33 grains. Got no pressure so I’ll probably go up on both from there. Both shooting 73 eldm, 1x fired hornady brass, with a Winchester primer. Bullet was seated a the hornady recommendation of 2.940. Both produced average velocitys in the 3100 range. Slight crosswind of 8-10 mph.

The staball 6.5 group was first group and had a es of approximately 70fps.

The varget group had an ES in the lower 20’s and is definitely minute of kill, IMO. Also the bullet by itself in the bottom right of the varget group was 100% me pulling the shot. I’m still counting it as part of the group though.

I’m going to stick with Varget unless staball gets its shit together with a higher charge weight. That’s a 9mm round for scale
 

Attachments

  • IMG_7595.jpeg
    IMG_7595.jpeg
    181.4 KB · Views: 25
  • IMG_7596.jpeg
    IMG_7596.jpeg
    198.3 KB · Views: 23

Marbles

WKR
Classified Approved
Joined
May 16, 2020
Messages
3,992
Location
AK
108 ELDM from a 17 inch factory T3x lite barrel with a AB Raptor 8 muffler. MV was 2826, but I had slight pressure signs (42 gr H4350). 41 gr of H4350 got me 2764 with no pressure signs. But, I only loaded 5, so no 10 round group. Edit: On second thought, the first 5 rounds had no pressure signs, it started raining and the second 5 got wet and all had slight ejector marks, so I think it was false pressure signs. End Edit
a31cf657-a71d-4f53-ba76-a1060abbe0c6.jpg

The group below is more reflective of my baseline shooting ability (prone, over a pack, with a contractor trash back laid out to keep the dust off).

45 gr of H4831sc (I labeled the group wrong as using the app to analyze this group was an afterthought as I new I would not be using the load due to velocity/pressure, ignore that), this got me 2721 fps and mild pressure signs.
29dea5e0-8fbf-4f86-91bc-22d32eb30ae8.jpg
 
Last edited:
  • Like
Reactions: Duh

walk2112

Lil-Rokslider
Joined
Oct 22, 2020
Messages
188
108 ELDM from a 17 inch factory T3x lite barrel with a AB Raptor 8 muffler. MV was 2826, but I had slight pressure signs (42 gr H4350). 41 gr of H4350 got me 2764 with no pressure signs. But, I only loaded 5, so no 10 round group. Edit: On second thought, the first 5 rounds had no pressure signs, it started raining and the second 5 got wet and all had slight ejector marks, so I think it was false pressure signs. End Edit
View attachment 730511

The group below is more reflective of my baseline shooting ability (prone, over a pack, with a contractor trash back laid out to keep the dust off).

45 gr of H4831sc (I labeled the group wrong as using the app to analyze this group was an afterthought as I new I would not be using the load due to velocity/pressure, ignore that), this got me 2721 fps and mild pressure signs.
View attachment 730512
I’ve never used the Hornady App, but is there something goofy here with the Group size value in MRAD’s? The inch value makes sense, but the conversion to MRADS looks like it thinks the inch measurement is at 450yards (ish).
Or I’m losing my mind… I suppose either possibility shouldn’t be ruled out haha

Every time I see good shooting short 6 creeds like this though, the urge to lighten my wallet again grows.
 

Marbles

WKR
Classified Approved
Joined
May 16, 2020
Messages
3,992
Location
AK
I’ve never used the Hornady App, but is there something goofy here with the Group size value in MRAD’s? The inch value makes sense, but the conversion to MRADS looks like it thinks the inch measurement is at 450yards (ish).
Or I’m losing my mind… I suppose either possibility shouldn’t be ruled out haha

Every time I see good shooting short 6 creeds like this though, the urge to lighten my wallet again grows.
I think the MRAD conversion is goofy. 0.88 inch should com out to 0.22 MRAD. Distance to target is set at 100 yards.

I wonder if the MRADs is something like zero angle? When I switch the app over to MOA it is giving me 0.38 MOA.
 
Joined
Aug 10, 2016
Messages
608
Location
Oregon
IMG_5404.jpeg
5 rounds prone. Then 5 shots done 1 at a time on a 10 second timer. Started standing and dropped into prone. Most shots broke with 1-2 seconds left on the timer. Tikka .223 with ADI factory 55gr Blitz

Upper right is a pressure test with another rifle.
 

Huntr

Lil-Rokslider
Joined
Apr 3, 2012
Messages
279
Location
Texas
Excited to post here with a lefty 223 Tikka. Picked it up from my FFL this week and took it to the range this morning I Went to staple a fresh target and just barely missed being struck by a rattlesnake. Needless to say my hear rate was pretty high for awhile. First 10 shot group with Black Hills 77gr. TMK. This will work for me!
 

Attachments

  • IMG_1545.jpeg
    IMG_1545.jpeg
    698.2 KB · Views: 23
  • IMG_1542.jpeg
    IMG_1542.jpeg
    326.9 KB · Views: 22

NSI

WKR
Shoot2HuntU
Joined
May 19, 2021
Messages
564
Location
Western Wyoming
Excited to post here with a lefty 223 Tikka. Picked it up from my FFL this week and took it to the range this morning I Went to staple a fresh target and just barely missed being struck by a rattlesnake. Needless to say my hear rate was pretty high for awhile. First 10 shot group with Black Hills 77gr. TMK. This will work for me!
Nice shooting! Right .2 and slip.

-J
 

waspocrew

WKR
Joined
Apr 2, 2022
Messages
306
Location
Billings, MT
I have over 1100 rounds on my 223 CTR and she's still shooting well (so probably just considered broken in haha). I'll have to try another 10 round group again and post it up.
 

5811

WKR
Joined
Jan 25, 2023
Messages
461
Here's 10 AAC 77tmk from a 16" tikka 223. Not bad for 80 cents a shot, factory loaded.


1000001977.jpg
 

walk2112

Lil-Rokslider
Joined
Oct 22, 2020
Messages
188
image_cropper_FED027B5-2D31-4324-BC3A-3685A7E5B791-834-000019313F2E5E03.jpeg
10 at 100 yards off Elite Iron bipod w/ Jellyfish rear bag, Tikka CTR 260 Rem with factory stock/bottom metal
 
Last edited:
Top