What did you do in the reloading room today?

[DB29]

Got new toy to clean case lube.

Sent from my iPhone using Tapatalk

If you put a funnel upside down over the threaded rod it speeds up the tumble quite a bit.

 

[mj23polaris]

If you put a funnel upside down over the threaded rod it speeds up the tumble quite a bit.

Good to know I’ll try it out


Sent from my iPhone using Tapatalk

 

[Sinistram]

If you put a funnel upside down over the threaded rod it speeds up the tumble quite a bit.

That's the first time I've heard that. Can you give some more context as to what the funnel does?

BTW - I love the clear lid on tumblers. I can't believe it took so long for manufacturers to figure that out.

 

[DB29]

That's the first time I've heard that. Can you give some more context as to what the funnel does?

BTW - I love the clear lid on tumblers. I can't believe it took so long for manufacturers to figure that out.

It’s science of some sort that I don’t understand. My best guess is the funnel causes stuff to go “downhill” which speeds up the tumble.

I read it on a review somewhere when I bought mine and tried it. I was pretty impressed with the improvement the funnel made.

 

[kkp005]

Loaded up 55 rounds of 6.5prc : 130gr tmk with n565

Loaded 35 rounds of 6mm creed : 95nbt with h4350

Primed 50 pieces of Lapua 223 brass

 

[Sinistram]

It’s science of some sort that I don’t understand. My best guess is the funnel causes stuff to go “downhill” which speeds up the tumble.

I read it on a review somewhere when I bought mine and tried it. I was pretty impressed with the improvement the funnel made.

So just "pointy side up" on the top of the tumbler and rock on?

 

[Caseknife]

So just "pointy side up" on the top of the tumbler and rock on?

Think its over the rod, but under the lid, poor in the brass and media. Neshiki rice works real good for media, less dust, cleans good. Another benefit of the funnel over the threaded rod is it would keep the brass away from the harder steel rod.

 

[DB29]

So just "pointy side up" on the top of the tumbler and rock on?

In the tumbler over the threaded rod like this.

 

[mj23polaris]

On the home stretch finally got around to annealing the rest of this years NRL barrels brass

Sent from my iPhone using Tapatalk

 

[waspocrew]

In the tumbler over the threaded rod like this.View attachment 853437

Gonna have to give this a try as well!

 

[Sinistram]

Loaded up a test batch of 300 Savage with some H335 and a 150gr Remington Core Lokt. I tested the same thing with Varget yesterday and got sub-optimal results from a known accurate rifle. Nothing under 2"!

I have about 10lbs of H335 on hand, so hopefully I can find yet another cartridge where it works well. If that doesn't give me what I'm after, I'll try H4895.

 

[Torque]

The next step in the reloading room is to put together 8, 10, and 12 ft. x 2" Oak bench tops. The wood from our mill is dried but I didn't have a space to join them. So, I built my first mobile work bench. The middle section is 2 Armor 54x25 dog hole tops. The base is white oak posts and a white oak bottom shelf from scrap I had left from sheathing the walls. I used Vevor leveling feet/wheels. The extensions are pine scrap from our mill. I didn't want to waste it. It may not be the best choice, but it will serve. I used the Rockler table extension kit and the left side in the pictures was my first attempt. The table is much too thick, and I was afraid the top wouldn't raise correctly unless I cut a bevel in the side that joins with the middle section. I was wrong. I abandoned the Rockler plans (which were good) because I was not attaching the kits using either of the methods they use. The top on the right I made 3/4" thinner, framed in white oak and did not bevel the joining edge. It worked great. (I am NOT going to go back and redo the first one, lol). Aside from the Armor tops I used oil based spar urethane (2 coats) on the entire project. It is what I had to hand. The measurements are 9'6"x54 with the extensions and 50"x 54" alone. This should last me the rest of my lifetime. It isn't perfect, but as a rank ametuer, I am happy with it.

Now, to the super fun task of putting benchtops together.

 

[DaveBarrows]

Prepped 40 25-06 casings getting ready to load up some test rounds with retumbo and IMR 4831. Speer 120 grain hot cor and 117 grain interlocks. Would like to try the 110 accubond but no luck.

 

[northernalpine]

Knocked out pressure, grouping for 223 load. Loaded the next 80/100 plus a refill on the 6.5CM loads.

 

[waspocrew]

Tested some 300 BLK subs again with Shooters World Blackout. On sale at Scheels for ~ $32/bottle is pretty tempting. Meters very well. Took 12 gr of powder with a 220 gr to reach around 1020 FPS. Ended up loading the other 205 projectiles I had left and will be ordering more.

 

[Pharmseller]

Prepped and primed 200 R-P headstamp .223 Rem cases.

Finished loading 600 Carlos yesterday.

Gonna load Kyle this week.





P

 

[Sandhills]

Yesterday but pulled bullets on more of my cousins old hand loads. For every five that are the mystery ball powder there's one that I assume is 4831 based on it being an extruded powder but I am still dumping all of the powder from them on the lawn when I get done

 

[Tx270WT]

Retuned a 243 predator load with the 75 gr vmax; getting near 5 SD around 3380 ft/s.

Testing a 300gr Sierra flat point jacketed bullet in the 45LC

 

[Pony Soldier]

I reached a point of the ultimate nightmare. CCI large rifle magnum have become as rare as a virgin in a whorehouse. When I went to winchester primers the results were not comparable. That occured as I completed a 1 lb can of H4350 and hornady quit making 175 gr interlock round nose bullets.

For this many variables I'm back to building a ladder on 0.1 gr increments to see if I can re-establish the consistancy I had for 45 years with differant parts.

 

[Lawnboi]

I reached a point of the ultimate nightmare. CCI large rifle magnum have become as rare as a virgin in a whorehouse. When I went to winchester primers the results were not comparable. That occured as I completed a 1 lb can of H4350 and hornady quit making 175 gr interlock round nose bullets.

For this many variables I'm back to building a ladder on 0.1 gr increments to see if I can re-establish the consistancy I had for 45 years with differant parts.

Scheels has some in stock and on sale if your near one with them in stock.

CCI 250 Magnum Large Rifle Primer Brick

SCHEELS.com

www.scheels.com

If that dosnt work blue collar has them

CCI #250 Magnum Large Rifle Primers

CCI #250 Magnum Large Rifle primers - 1000ct Box

www.bluecollarreloading.com

Let me know who to bill the finders fee to.