What did you do in the reloading room today?

[The_Whitetail_Kid]

Loaded up some loads to retest with my 6.5x284 with once fired brass to see what it does to the the velocity and pressure compared to new brass.

 

[jphares44]

Just annealed 100 pieces of Peterson 7mm Rem Mag brass, using a buddy's AMP annealer. Man, I gotta get me one of these!

 

[Harvey_NW]

6.5 PRC tinkering…shot pressure tests for StaBALL HD and N565 with 143gr ELD-Xs to see if they offer any improvements on H1000.

I didn't see what primer you're using but I have the same rifle and initially tested 57gr H1000 with a magnum primer and got 2950 out of it new, but ES was a little wild which I assumed was from the barrel being new. Approaching 200rds now and about to retest with a magnum primer to see if I can get some free juice. Might be worth a try if you're not doing so already.

 

[northernalpine]

I didn't see what primer you're using but I have the same rifle and initially tested 57gr H1000 with a magnum primer and got 2950 out of it new, but ES was a little wild which I assumed was from the barrel being new. Approaching 200rds now and about to retest with a magnum primer to see if I can get some free juice. Might be worth a try if you're not doing so already.

Fed 215M primers

No doubt on your load recommendation. The load that is working the best for accuracy/velocity is 57.8gr of H1000 but my velocity is ~100fps less than what you are getting. I’m also at ~500’ MSL which has some negative effects.

 

[Harvey_NW]

Fed 215M primers

No doubt on your load recommendation. The load that is working the best for accuracy/velocity is 57.8gr of H1000 but my velocity is ~100fps less than what you are getting. I’m also at ~500’ MSL which has some negative effects.

Once I got some rounds on it I settled on 57gr with a CCI 200 @ 2850 and it's been very consistent, but I'm still curious if I can get some free velocity with more pop. Factory Tikka barrels just tend to be a bit slower than the cut rifled.

 

[deertrout]

Been pretty busy lately but finally got back to reloading my first batch of cartridges. Went with 50gr TSX, and a ladder of H335 from 23.4gr to 24.6gr in 0.3 grain increments, 4 shots per charge. Trying to figure out a good charge for my 223 Gen II Ruger American. Really, though, I just wanted to get through all the steps in the process for the first time before I start down the full experimentation rabbit hole. Sat this batch to book COL. I'm not sold this is the best powder for this bullet but it was what was available locally. I definitely want to experiment with a few others. Snowing pretty good here this morning, supposed to calm down around lunch so hopefully the forecast holds I can shoot these past the Garmin today and see how they group.

 

[HGL]

Loaded up some 103 ELDx for testing in my new 6mm creedmoor barrel. Osprey, 1-7 twist, finished at 19" on my Tikka. I was pleasantly suprised at the speeds I got with the short tube.







Osprey 3b contour, looks very similar to a CTR profile from what I can tell. They turn the shank down to the Tikka OD.





Going to explore 1, 6, and 8 a bit more, but it looks promising. (end up being 4 shot groups, as the 1st shot is chronoed with the magneto attached, yep a Garmin would be sweet...) Going to load up 15 of each contender today and re-test. My first "Osprey" barrel but so far so good. Seems plenty accurate and cleans up fast, very little copper fouling through my first 100 rounds or so.

 

[Mulyhuntr]

Once I got some rounds on it I settled on 57gr with a CCI 200 @ 2850 and it's been very consistent, but I'm still curious if I can get some free velocity with more pop. Factory Tikka barrels just tend to be a bit slower than the cut rifled.

Juice doesn't seem worth the squeeze to go prc. Lots of posts about underwhelming velocity lately. 6.5cm tikka can push close to 2750 with rl16 and a 147.

 

[digger]

I prepped a bunch of ADG 7 prc brass and loading a test batch now

 

[Houseminer]

Yesterday kicked out 400 9mms. My back didnt let me finish the run of 500 I was going for. So I took to the drafting table to make a new shooting bench. Got my lumber list ready will head to the yard this morning.

 

[N2TRKYS]

Loaded some 6.5 Creedmoor

 

[eoperator]

View attachment 684867

Those are some impressive numbers for a 19" barrel & h4350.

 

[RCL]

Prepped 200 once fired 223 brass for reloading.
Have some Calhoon bullets I am anxious to try.

 

[6MT]

Loaded some 6.5 Creedmoor

What did you load? (Bullets, powder, primer, etc.)

 

[N2TRKYS]

What did you load? (Bullets, powder, primer, etc.)

StaBall 6.5 powder, 143 grain eld-x bullets for practice and some with 140 grain Accubond bullets hunting loads with Fed210 primers in all. Nosler brass

 

[6MT]

Nice! Do you know the velocity?

 

[JasonWi]

Hung two Koda 46” 8000 lumen LED lights above my bench. Really improved the visibility

 

[N2TRKYS]

Nice! Do you know the velocity?

I think you’re talking to me: 143 eld-x = 2750fps 140 grain Accubonds = 2800fps.

If you’re not talking to me, my bad.

 

[6MT]

I think you’re talking to me: 143 eld-x = 2750fps 140 grain Accubonds = 2800fps.

If you’re not talking to me, my bad.

Yep, it was me talking to you. I was curious about the 140’s. I’m getting 2800fps with a 26” barrel.

 

[N2TRKYS]

Yep, it was me talking to you. I was curious about the 140’s. I’m getting 2800fps with a 26” barrel.

Mine’s out of a Tikka Lite, so I believe a 24” barrel.