The 22 creedmoor thread

[khuber84]

You don't worry about case fill with the bullet seated out so much? For hunting, I worry that the powder column on steep shots could affect internal ballistics (think downhill shot where powder is not packed against primer flash hole).

This is why I'm hesitant to use just H4350 at 41-ish grains...

N555 is FULL at 43.5gr, H4350 doesn't give any issues either tho.

 

[wind gypsy]

You don't worry about case fill with the bullet seated out so much? For hunting, I worry that the powder column on steep shots could affect internal ballistics (think downhill shot where powder is not packed against primer flash hole).

This is why I'm hesitant to use just H4350 at 41-ish grains...

41 gr h4350 is plenty case fill.

 

[FB Trout]

Muley buck that was jumped out of its bed at 80 yards, impact velocity of 2880ish fps with 88 ELDm. Buck was sharply quartered away while running, bullet hit right at base of the backstrap, above shoulder. The deer dropped and when approached had a few agonal breaths, then expired. The backstrap in the area was destroyed, heavy bone fragmentation with bone or bullet fragments that entered upper thoracic cavity and upper lobes of lungs. Bullet was through and through the strap/bone.

 

[HighUintas]

These pics make me think if I hunt w a 22 I'll not use a 22creed haha. Total destruction with it

 

[The Fish Box]

Okay what am I doing wrong? Redding type S dies new alpha munitions brass with 77gr tmk. I bought a VLD seating stem because the stem that came with the dies did the same damn thing.

 

[Juan_ID]

Okay what am I doing wrong? Redding type S dies new alpha munitions brass with 77gr tmk. I bought a VLD seating stem because the stem that came with the dies did the same damn thing. View attachment 794723

Did you chamfer the case mouths?

 

[waspocrew]

My alpha brass had very tight necks, so I ran a mandrel though them and it stopped deforming projectiles. I'd also make sure you've chamfer/deburred the case mouth.

 

[4090Sharps]

My alpha brass had very tight necks, so I ran a mandrel though them and it stopped deforming projectiles. I'd also make sure you've chamfer/deburred the case mouth.

Definitely looks like the result of a tight neck.

 

[Gstew1930]

My alpha brass had very tight necks, so I ran a mandrel though them and it stopped deforming projectiles. I'd also make sure you've chamfer/deburred the case mouth.

Same

 

[The Fish Box]

I did a light chamfer and ran some graphite around the necks and that was the result. Maybe I’ll just live with it and hope it gets better after resizing. I hate running fresh brass thru too many extra processes.

 

[waspocrew]

I did a light chamfer and ran some graphite around the necks and that was the result. Maybe I’ll just live with it and hope it gets better after resizing. I hate running fresh brass thru too many extra processes.

For what it's worth, since the initial hiccup requiring a mandrel to open the necks, the brass has been fine. Haven't needed to use a mandrel again. Just size and seat like normal.

 

[sturner88]

Large, mature, Montana Mulie. Spent the whole year anticipating a long range shot, only to shoot him at 45 yard.

 

[waspocrew]

Large, mature, Montana Mulie. Spent the whole year anticipating a long range shot, only to shoot him at 45 yard.

Damn! Look at the neck on that thing!

 

[mxgsfmdpx]

Large, mature, Montana Mulie. Spent the whole year anticipating a long range shot, only to shoot him at 45 yard.

What bullet?

 

[sturner88]

What bullet?

75 eldm