Silencerco Scythe TI review

[HighUintas]

I'd bet this issue is more of a weld issue than a design issue, based on some of the reports on failures vs non-failures.

 

[wind gypsy]

Would you rather get hit with high pressure water from a 1” hose or water at the same pressure from a 2” hose?

 

[dreadi]

Yes.

Whose front cap is that?

 

[Marbles]

Whose front cap is that?

Hanson Brothers Bravo Ti

Hansohn Bravo Titanium Front Cap – Hansohn Brothers

hansohnbrothers.com

 

[dreadi]

Hanson Brothers Bravo Ti

Hansohn Bravo Titanium Front Cap – Hansohn Brothers

hansohnbrothers.com

Thank you. Reading is fundamental. All I saw was an image and no copy

 

[B_Reynolds_AK]

Sorry if I missed it but has anyone shot 6mm through either the silencerco or hansohn 5.56 end cap?

Anyone who did, likely only did it once!

Yes, I posted on this. The SilencerCo Ti 556 end cap diameter is fine for 6mm. It is actually larger than some 6.5mm end caps. I have quite a few rounds through it in this configuration.

 

[B_Reynolds_AK]

Just got the Wolfhunter in and was surprised at the length to girth ratio difference between the two. They weigh within .1 oz of each other.

My Scythe now weighs 8.7 oz, while the Wolfhunter weighs 8.8 oz.

I guess it’s time to clean my Scythe!

 

[DB29]

Just got the Wolfhunter in and was surprised at the length to girth ratio difference between the two. They weigh within .1 oz of each other.

My Scythe now weighs 8.7 oz, while the Wolfhunter weighs 8.8 oz.

I guess it’s time to clean my Scythe!

View attachment 808372

Very interested to hear what you think about the sound and recoil reduction between the 2.

 

[kswaterfowl]

Just got the Wolfhunter in and was surprised at the length to girth ratio difference between the two. They weigh within .1 oz of each other.

My Scythe now weighs 8.7 oz, while the Wolfhunter weighs 8.8 oz.

I guess it’s time to clean my Scythe!

View attachment 808372

I think i need to buy another one of those woflhunters.

 

[Jbehredt]

I got mine yesterday. It will primarily live on my 223 with a Hanson Brothers 5.56 cap, but will probably see the 243 at some point. If I get something with larger case capacity than a 308, I will probably use my Raptor 8 instead after these reports. Particularly as I like 16 inch barrels.

View attachment 808316

Looks like my stocking just got .6 oz heavier!

 

[HuntHarder]

What is the benefit / disadvantage of swapping out the front 30 cap with break built in to the Hanson brothers end cap?

 

[Marbles]

What is the benefit / disadvantage of swapping out the front 30 cap with break built in to the Hanson brothers end cap?

Advantage: reduce noise, about 1/4 inch shorter, easier to tape over, and 0.4 oz lighter (if that matters to anyone).

Disadvantage: Increased recoil, and if you get a smaller diameter you have to remember not to shoot anything over 6mm through it (though based on how tight the Wolfhunter is, if you check with an alignment rod you can get away with perhaps up to 7mm, but, that is a game one plays at their own risk).

 

[HuntHarder]

Advantage: reduce noise, about 1/4 inch shorter, easier to tape over, and 0.4 oz lighter (if that matters to anyone).

Disadvantage: Increased recoil, and if you get a smaller diameter you have to remember not to shoot anything over 6mm through it (though based on how tight the Wolfhunter is, if you check with an alignment rod you can get away with perhaps up to 7mm, but, that is a game one plays at their own risk).

Thank you. Mine is mainly on my 6.5 BB, so I suppose I will steer clear and resist the urge to buy one.

 

[Marbles]

Thank you. Mine is mainly on my 6.5 BB, so I suppose I will steer clear and resist the urge to buy one.

Yeah, for a 6.5 I doubt the 30 cal flat cap is worth it.

 

[B_Reynolds_AK]

What is the benefit / disadvantage of swapping out the front 30 cap with break built in to the Hanson brothers end cap?

That is the SilencerCo Ti .223 end cap. Its diameter is fine for use on a 6 mm, which I have been. Point was to reduce noise further. It does.

 

[WyldGoose]

Another advantage to flat front caps is less holes/nooks/crannies for debris to find its way into.

 

[wind gypsy]

Another advantage to flat front caps is less holes/nooks/crannies for debris to find its way into.

This is the primary reason i use a flat cap on mine for hunting season. Easier to tape one hole than the whole circumference of a brake in addition to the one hole.

 

[WyldGoose]

This is the primary reason i use a flat cap on mine for hunting season. Easier to tape one hole than the whole circumference of a brake in addition to the one hole.

Yep.
Before I got my Scythe, it’s the first thing I did years back to my Omega 300, plus on that one it reduced the OAL by like 1.5”.

 

[HuntHarder]

This is the primary reason i use a flat cap on mine for hunting season. Easier to tape one hole than the whole circumference of a brake in addition to the one hole.

I'm thinking I tape the end of my barrel different than you. . I usually put 1 piece across the muzzle, then atleast a wrap or 2 around to hold initial piece

 

[Ishootgunssometimes]

Any thoughts on Scythe Ti vs 6ix+ Ti?