Silencerco Scythe TI review

[WyldGoose]

Sorry if I missed it but has anyone shot 6mm through either the silencerco or hansohn 5.56 end cap?

I do. Hansohn Bros told me their 5.56 cap is good up to 6mm. I’ve got just under 150 rounds of 6cm through mine without a single issue.

 

[Ishootgunssometimes]

Idk I’m in the market for a can and if I find a deal on a scythe I’d prob still go for it.

 

[Yfz04drt]

Diligent Defense Enticer STI. About an once heavier, one inch longer, cheaper and probably quieter but not quite as cool as the Scythe according to the cool kids

I've been looking for one and everywhere is OOS.

 

[BBob]

I've been looking for one and everywhere is OOS.

Wow, it's seemed like they were available everywhere recently. I'll check my LGS tomorrow when I head that way. They've had them in stock continuously for awhile.

 

[sticman77]

I’ve got one of these in jail, purchased after seeing the reviews here… and now slightly worried. I think I should be fine though it’s going on a 7mm rem mag 24”?

 

[Tahoe1305]

Not positive it was linked here. If so another won’t hurt for visibility.

Poll on failures with stats below:

SilencerCo Scythe Ti failures

If you’ve experienced catastrophic failure of the Scythe Ti, please post the following: 1. Cartridge or cartridges used with approximate round count 2. Barrel length 3. Factory ammo, hand loads or both 4. Details of ammunition 5. Details of failure (to include failure point and pics)

rokslide.com

 

[HuntHarder]

When they become available, it seems as though a bunch become available at a time. In talking with Silencerco, they said that capital armory and silencer shop tend to get them first in stock. I was lucky and it only took a couple weeks for mine to come in. So far so good, but treading lightly going forward.

 

[Tdonat]

I’ve got one of these in jail, purchased after seeing the reviews here… and now slightly worried. I think I should be fine though it’s going on a 7mm rem mag 24”?

I wouldn’t worry with a 24” 7 mag. My scythe blew up on an 18” saum. It’s going back on there once I get it back, I have faith that it’ll be good to go once I have it fixed. My brother runs one on a 24” 6.5 PRC without issue for 700ish rounds now

 

[Yfz04drt]

Wow, it's seemed like they were available everywhere recently. I'll check my LGS tomorrow when I head that way. They've had them in stock continuously for awhile.

I actually just got a response from a dealer that says they'll have them next week. Fingers crossed.

 

[sticman77]

I wouldn’t worry with a 24” 7 mag. My scythe blew up on an 18” saum. It’s going back on there once I get it back, I have faith that it’ll be good to go once I have it fixed. My brother runs one on a 24” 6.5 PRC without issue for 700ish rounds now

thats good to hear, it will take me a while to get to that round count, and i have no plans on chopping this barrel.

 

[HighUintas]

I have an original Dead Air Nomad and other cans for other things. But I want this can to be shorter and lighter, and it needs to work on at least the short 30-06.

I don't think I'd worry about a 20" '06. Even though it's the same capacity as a prc, that is going to be less pressure at the muzzle than a 20" 6.5 prc

 

[Okie_Poke]

I don't think I'd worry about a 20" '06. Even though it's the same capacity as a prc, that is going to be less pressure at the muzzle than a 20" 6.5 prc

Please educate me. Because 60k vs 65k psi SAAMI chamber pressures or something else?

 

[HighUintas]

Please educate me. Because 60k vs 65k psi SAAMI chamber pressures or something else?

Ya. Saami '06 is 57k or 60k.... Something like that. Prc is either 63k or 65k.

Then there is also the bore diameter. For the same length barrel, for a given starting pressure, the larger diameter bore would drop in pressure more by the end of the barrel due to a larger volume of expansion of the hot gases.... If that makes sense. I'm explaining it terribly.

That would of course be slightly dependent on the powder type used, but overall the pressure drop would be greater for the '06.

 

[Okie_Poke]

Ya. Saami '06 is 57k or 60k.... Something like that. Prc is either 63k or 65k.

Then there is also the bore diameter. For the same length barrel, for a given starting pressure, the larger diameter bore would drop in pressure more by the end of the barrel due to a larger volume of expansion of the hot gases.... If that makes sense. I'm explaining it terribly.

That would of course be slightly dependent on the powder type used, but overall the pressure drop would be greater for the '06.

I understand the bore diameter/area part. But I would kinda expect the different powder burn speeds to equalize things a bit. But I honestly have no idea.

 

[sticman77]

I actually just got a response from a dealer that says they'll have them next week. Fingers crossed.

Modern Warriors has them in stock. I’ve ordered 3 suppressors from them. Takes about 3 biz days to ship to LGS.

 

[wind gypsy]

Ya. Saami '06 is 57k or 60k.... Something like that. Prc is either 63k or 65k.

Then there is also the bore diameter. For the same length barrel, for a given starting pressure, the larger diameter bore would drop in pressure more by the end of the barrel due to a larger volume of expansion of the hot gases.... If that makes sense. I'm explaining it terribly.

That would of course be slightly dependent on the powder type used, but overall the pressure drop would be greater for the '06.

I used to assume more overbore = harder on suppressors but was told it’s more a function of how much powder is burning and actually same amount of powder and pressure but in a bigger bore was harder on suppressors because that pressure exists over a bigger cross section.

 

[Marbles]

I got mine yesterday. It will primarily live on my 223 with a Hanson Brothers 5.56 cap, but will probably see the 243 at some point. If I get something with larger case capacity than a 308, I will probably use my Raptor 8 instead after these reports. Particularly as I like 16 inch barrels.

 

[DisplacedHusky]

I got mine yesterday. It will primarily live on my 223 with a Hanson Brothers 5.56 cap, but will probably see the 243 at some point. If I get something with larger case capacity than a 308, I will probably use my Raptor 8 instead after these reports. Particularly as I like 16 inch barrels.

View attachment 808316

Is that weight for direct thread?