Silencerco Scythe TI review

[Q_Sertorius]

Another let go today View attachment 806929View attachment 806930

Do you mind sharing the circumstances of the failure?


Sent from my iPhone using Tapatalk

 

[Raghornklr]

6.8 western, 2.955” coal 175tgk 2775fps
532 rounds
Cleaned once 100 rounds ago.

Cold bore second shot off a bench

 

[WI-Carcosa]

6.8 western, 2.955” coal 175tgk 2775fps
532 rounds
Cleaned once 100 rounds ago.

Cold bore second shot off a bench

Barrel length?

 

[Raghornklr]

20”

 

[WI-Carcosa]

20”

Thank you! Well now I’m getting more nervous about using this on a 20” 6.5 PRC

 

[waspocrew]

Is it the same weld failing every time? I agree - I think their numbers are likely suspect as well. My interest in this can is for smaller applications - Howa Mini 6 ARC, 300 BLK, 6 CM. But definitely disappointed to see this may not handle my 22" 300 PRC or even my 21" 6.5 PRC.

 

[Muledeerfanatic]

Well this is great
Just read all this
Now I wish I bought a DD STI

 

[Runwilderness]

Thank you! Well now I’m getting more nervous about using this on a 20” 6.5 PRC

Same boat here. Mine will start life on 6.5 Swede, but I’ve got a tikka 6.5 PRC take off in the safe. I’m now wondering if I should sell the barrel and magnum bolt and get on the small caliber train…

 

[WI-Carcosa]

Same boat here. Mine will start life on 6.5 Swede, but I’ve got a tikka 6.5 PRC take off in the safe. I’m now wondering if I should sell the barrel and magnum bolt and get on the small caliber train…

Given the failures I have a 19” t3 Swede that I am skeptical to use now with it. Might be an expensive 223 can worst case I guess or on a 26” wsm. Mine should be at my door in the next 2 weeks and I picked up a laser thermometer to keep a keen eye on it.

 

[mt100gr.]

Given the failures I have a 19” t3 Swede that I am skeptical to use now with it. Might be an expensive 223 can worst case I guess or on a 26” wsm. Mine should be at my door in the next 2 weeks and I picked up a laser thermometer to keep a keen eye on it.

I have to think that non-magnum cartridges with over 16" barrels would be perfect for the Scythe....

Have there been any reported (here on Rokslide) failures from use exclusively on standard bolt face rifles???

 

[Runwilderness]

Given the failures I have a 19” t3 Swede that I am skeptical to use now with it. Might be an expensive 223 can worst case I guess or on a 26” wsm. Mine should be at my door in the next 2 weeks and I picked up a laser thermometer to keep a keen eye on it.

Thanks. Mine should be here shortly after Xmas, but I haven’t cut/threaded the Swede yet (I was debating the length when this thread blew up, leaning 20” now), so it’ll be a bit before I have enough rounds down the pipe. I’ll keep this thread updated too.

I bought the Scythe based on the earlier posts and wanting something light and short to hunt with…if I’m stuck with 223 or bust, then I’m definitely going to find myself in the 223 for everything thread.

 

[Amos Moses]

Bought one yesterday afternoon and discovered the more recent posts here last night. Canceled the purchase before the paperwork was sent in and switched to a gen 2 Ultra 7. Really hope they iron this out because all the stats are impressive.

 

[B23]

Are these all pretty much coming apart at the same spot or is it a mix of different places where they're coming apart at?

 

[pods8 (Rugged Stitching)]

Of the 3 failure photos posted two were the same weld, one was the next one.

 

[13bonatter69]

Dang I was getting ready to order one of these for a Springfield redline 308 with a 16 inch barrel tomorrow. Even though the 308 isnt a magnum the 16 inch barrel has me worried.....lol I had my mind set on this because of its size.....I have not even thought about a second choice.....???

 

[BBob]

I have not even thought about a second choice.....???

Diligent Defense Enticer STI. About an once heavier, one inch longer, cheaper and probably quieter but not quite as cool as the Scythe according to the cool kids

 

[walk2112]

Dang I was getting ready to order one of these for a Springfield redline 308 with a 16 inch barrel tomorrow. Even though the 308 isnt a magnum the 16 inch barrel has me worried.....lol I had my mind set on this because of its size.....I have not even thought about a second choice.....???

Otter Creek Hydrogen S would be good.

 

[Tdonat]

Dang I was getting ready to order one of these for a Springfield redline 308 with a 16 inch barrel tomorrow. Even though the 308 isnt a magnum the 16 inch barrel has me worried.....lol I had my mind set on this because of its size.....I have not even thought about a second choice.....???

If it makes you feel any better, mine had well over 2k of 22” 6.5 creed before it let go on my 18” saum. I would imagine a 16” 308 would be fine. My brothers has probably 6-800 of 24” 6.5 PRC and no issues yet