Lightest reliable pic rings?

Marbles

WKR
Classified Approved
Joined
May 16, 2020
Messages
4,473
Location
AK
I had a scope in some QD rings on an AR. I never found that you could actually hold a reliable zero when taking them on and off. Always had to re-zero if you wanted something better than 10MOA from where you sighted it. I figured it was for the guys that only bore sighted and said good nuff and went hunting.
I've had better luck, both with my Kimber and my AR. Usually no adjustment is needed.
 

Marbles

WKR
Classified Approved
Joined
May 16, 2020
Messages
4,473
Location
AK
I was thinking of farrell low or Swfa low with Leupold pic rail on my kimber 270, depending on clearance. Im putting a swfa 3-9 on my Montana. Anyone tried low farrell rings on a kimber?
A. Look up the hight of your rail.
B. Look up the hight of your rings to center.
C. Look of the outer diameter of your objective.

If A+B equals or is greater than C/2 it will fit (The top of the action is slightly higher than the top of the barrel).
 

Dobermann

WKR
Joined
Sep 17, 2016
Messages
1,942
Location
EnZed
I use the sportsmatch on my tikkas but this thread is specifically for my Kimber.
Got it.

The first post said "a few of my rifles"; don't think it mentioned the Kimber.

I'll leave the info about the Spuhr and link to the rail thread in case that's helpful for anyone else. :)
 
OP
thinhorn_AK

thinhorn_AK

"DADDY"
Joined
Jul 2, 2016
Messages
11,231
Location
Alaska
Got it.

The first post said "a few of my rifles"; don't think it mentioned the Kimber.

I'll leave the info about the Spuhr and link to the rail thread in case that's helpful for anyone else. :)
I don’t care, I was just hoping for info about rings that would go on a rail. Feel free to post whatever you want.
 

Marbles

WKR
Classified Approved
Joined
May 16, 2020
Messages
4,473
Location
AK
I don’t care, I was just hoping for info about rings that would go on a rail. Feel free to post whatever you want.
Not that you asked, but for weight my rail and NF low rings come in at 4.3 ounces. I took a hacksaw to the rail though. I shortened it, and the side cut gives easier access to the blind magazine while maintaining the advantages of a one piece rail.20200705_180644.jpg
 

SDHNTR

WKR
Joined
Aug 30, 2012
Messages
7,109
Not that you asked, but for weight my rail and NF low rings come in at 4.3 ounces. I took a hacksaw to the rail though. I shortened it, and the side cut gives easier access to the blind magazine while maintaining the advantages of a one piece rail.View attachment 497236
I have thought for a long while, why doesn’t any manufacturer do exactly this?
 
OP
thinhorn_AK

thinhorn_AK

"DADDY"
Joined
Jul 2, 2016
Messages
11,231
Location
Alaska
I have been very happy with Leupold PRW2 rings and would also add another vote for Burris XTR two-piece bases. They are not the tacticool chunky aluminum rings that everyone now thinks they need, but they have held up perfectly over the last 10 years and are machined from steel.

Again, they don’t have those bases for the rifle I’m dealing with. If they did, that’s what I’d get.
 
Joined
Jan 5, 2022
Messages
746
I have thought for a long while, why doesn’t any manufacturer do exactly this?
They used to. IIRC, They were Bushnell or B&L. I have one for a lefty 700. Slots are weaver, but they can be opened up for pic rings.

s-l400.jpg
 

BarCO

Lil-Rokslider
Classified Approved
Joined
Jan 6, 2023
Messages
299
I really like my Hawkins hybrids. No pic rail needed.
I have a set as well but since they are directional I can’t quite get it far enough back with SHV, so 3-9 SWFA going on instead. This is a short action.
 

Attachments

  • 92A14AE9-2685-4C83-ACC3-05083784A449.jpeg
    92A14AE9-2685-4C83-ACC3-05083784A449.jpeg
    505.7 KB · Views: 46

BarCO

Lil-Rokslider
Classified Approved
Joined
Jan 6, 2023
Messages
299
The SWFA are basically free compared to others it seems. Are the 1” inserts they come with solid?
 
Joined
Jan 5, 2022
Messages
746
The SWFA are basically free compared to others it seems. Are the 1” inserts they come with solid?
Most likely; but finding a solid 1" scope is the problem with that approach.

I haven't ever used the inserts.

Sometimes they are free: The first sets I used came as package deals for sales, and the rings were basically thrown in for free.
 
Top