What did you do in the reloading room today?

[Pharmseller]

Loaded 300 Kyle to go along with the 200 I already had.

 

[49ereric]

Primed 200 of 600 357 mag cases this evening.

 

[Ac338]

I’m in the process of moving my reloading/ bow shop and hunting gear into an upstairs room from the basement. Was able to get one gun rack up and made a start on the baseboards. Hope to finish that and get the Gridwall up and start moving benches and tools up from the basement within a week. I’m definitely ready to get back to loading instead of working on this. Should be a lot more room coming from a small basement bench into a whole room. It’ll be nice getting the gear out of totes and onto the Gridwall.

 

[GoWyo!]

Loaded up 4 different .338 WM loads with 275 gr Speers. 60 rds.

 

[waspocrew]

Ran 500 cases of 38 Special through the expander tonight. Just need to load. Shot some plated 125 gr flat noses out of the 16” Marlin and they were all supersonic. I’ll drop the charge a bit more and see where we land.

 

[NastyN8]

Deprimed and resized 100 6.5 Grendel and 132 7mm PRC

Just getting started with the whole process. Been saving brass for years, now getting going reloading.

 

[Sinistram]

Primed 200 of 600 357 mag cases this evening.

What's your priming tool of choice for these?

 

[49ereric]

What's your priming tool of choice for these?

Rcbs ram priming tool. Lee hand primer I got decades ago broke long ago.
Stone Age reloader here…

 

[Quandary]

Just pulled all of my office furniture out of my room and added a bigger bench which I set up low enough so that I could sit in a normal chair while dumping powder.

 

[sierracharlie338]

Just pulled all of my office furniture out of my room and added a bigger bench which I set up low enough so that I could sit in a normal chair while dumping powder.

View attachment 1049377View attachment 1049378View attachment 1049379

Nice. Looks like a good usable space.

 

[Backcast88]

Shot some really good groups with my new Tikka 270 Win. and loaded the best groups again to validate some stuff.

140 TGK and RL23 x6
130 AB and n160 x6
135 SMK and n160 x12

 

[NastyN8]

Just pulled all of my office furniture out of my room and added a bigger bench which I set up low enough so that I could sit in a normal chair while dumping powder.

View attachment 1049377View attachment 1049378View attachment 1049379

Quandary I’ve seen those stands you have your presses on, what are they? Where do you get them? What are the advantages?

 

[MD97756]

Inline fabrication stands. Great product, local Oregon company.

 

[2Stamp]

I'm finishing the top of the bench and the configuration a bit. New 1/2" top will get routed for t-track to be installed. Wood stand made for my new Forster Co-ax. I need to figure out at what measurements to put the t-track, which should be here this weekend.

The Before. We'll see how it turns out.

 

[sierracharlie338]

Inline fabrication stands. Great product, local Oregon company.

I have a couple of these as well. I second this.

 

[Quandary]

Quandary I’ve seen those stands you have your presses on, what are they? Where do you get them? What are the advantages?

I have the bench height set at 32" so raising the presses makes them more comfortable to run.

 

[NastyN8]

I forgot we finally setup our reloading area also.

Learning a lot from you guys. Tips, tricks, what’s needed and not. Starting simple and will see what else we need for comfort and time efficiency. Only so much time and I much prefer hunting and shooting to reloading, but really can’t wait to start rolling my own and doing load dev for a couple rifle/cartridge combos. Thanks again yall. Back to lurking

 

[49ereric]

Primed another 200 357 mag cases this evening.

 

[sierracharlie338]

I forgot we finally setup our reloading area also.

Learning a lot from you guys. Tips, tricks, what’s needed and not. Starting simple and will see what else we need for comfort and time efficiency. Only so much time and I much prefer hunting and shooting to reloading, but really can’t wait to start rolling my own and doing load dev for a couple rifle/cartridge combos. Thanks again yall. Back to lurking

That’s 100 times better than anything I had starting out. Nice set up!

 

[sierracharlie338]

Primed another 200 357 mag cases this evening.

You’re an over achiever