Unknown Suppressors Updates

[nm.otter]

Have you guys done any testing of dedicated .17 designs? Given the low gas volume and high projectile velocity, I'm curious what effect bore diameter might have on performance.

 

[ID-Muley]

Have you guys done any testing of dedicated .17 designs? Given the low gas volume and high projectile velocity, I'm curious what effect bore diameter might have on performance.

Definitely no dedicated 17 designs but are you talking rimfire?

 

[nm.otter]

Not a new design per se, just a tighter bore on one of your .224 cans.

.17 HMR, specifically. Snappy little buggers, curious if a smaller-than-.22 (plus clearance) bore would do anything.

 

[Bluumoon]

@Unknown Suppressors was just at my FFL filing paperwork and looking at in stock suppressors. You guys might want to consider a 4” sticker that says “over the barrel” for retail sales, otherwise I bet most people would look past them at first glance just thinking they are another long suppresor.

OG6.5 w my chosen sn is

 

[Rainyday]

@Unknown Suppressors Has there been any news about getting your cans on SilencerShop?

 

[wind gypsy]

I'm curious about progress on the NHS.

 

[lintond]

I'm curious about progress on the NHS.

I was told less than a month via message a week ago. I’m eager for the NHS for my comp gun

 

[Formidilosus]

I'm curious about progress on the NHS.

It’s done as far as I know.




On the above 6UM, on sandbags the reticle moves down 2 mils. Even on a 9.5lb 6.5cm it recoils down .5 to 1.0 mils or so.

 

[wind gypsy]

It’s done as far as I know.

View attachment 1003114


On the above 6UM, on sandbags the reticle moves down 2 mils. Even on a 9.5lb 6.5cm it recoils down .5 to 1.0 mils or so.

Is that even a good thing to have that much downward force on the muzzle?

 

[Formidilosus]

Is that even a good thing to have that much downward force on the muzzle?

In general no. But that can isn’t made for rifles and cartridges that recoil- it’s made for small 6mm PRS guns.

It is kind of neat that if you use a reticle that has no top post or marks above center, it drops the reticle so that you spot the shot in the cleanest, most open part of the view.

 

[dårlig jeger]

Would US entertain the idea of doing a small run of OG7 cans? Just a 7mm version of the OG6.5? I like the idea of an OG 6.5 but would like to use it on 7prc as well.

I can see it not being worth it to develop and sell such a can between the 6.5 and OG versions, but maybe a single batch with enough commitments?

 

[Formidilosus]

Would US entertain the idea of doing a small run of OG7 cans? Just a 7mm version of the OG6.5? I like the idea of an OG 6.5 but would like to use it on 7prc as well.

I can see it not being worth it to develop and sell such a can between the 6.5 and OG versions, but maybe a single batch with enough commitments?

You can use a 7mm with the OG65. Just check alignment.

 

[WiscoHoundsman]

@Formidilosus do you happen to know if the 6.5mm end cap for a reaper will fit a 7mm projectile through it more than once?

 

[Formidilosus]

@Formidilosus do you happen to know if the 6.5mm end cap for a reaper will fit a 7mm projectile through it more than once?

Yes. Just check alignment. However, end caps are cheap enough that I would just swap it probably.