Tikka updating 300 wsm twist rate- 1-10”

Regardless of your application bullets are not stable forever once they leave the barrel.
I never said it was stable forever. In answering a question about “stable forever” , l wrote about gyroscopic stability continuing to increase as it goes down range and slows down.

For practical hunting applications, “dynamical” (sic) stability is a non-issue
 
I never said it was stable forever. In answering a question about “stable forever” , l wrote about gyroscopic stability continuing to increase as it goes down range and slows down.

For practical hunting applications, “dynamical” (sic) stability is a non-issue
"A bullet has its' least stability leaving the muzzle." Least gyroscopic stability. I've had loads that open up at 300 yards well before they went transonic but looked great at 100. Not sure if that is stability related. If youre going to hunt with it you gotta take it out to the range you plan to hunt if you want to be sure.
 
Case in point: MDT has a video where they fired a bullet backwards out of the case, was obviously flying straight a few feet out of the gun, and it was sort of stable till 100yds, then spun and fell out of the sky by 600 yds. The bullet was not aerodynamically stable to begin with, in stark contrast to any forward-facing modern bullet.

Here's a great discussion of twist rate that is refreshingly informative from the Hornady Podcast. It is explained how a bullet (forward-facing, obviously) is more unstable as it leaves the barrel and becomes increasingly stable as it slows in horizontal velocity, while the rotational velocity reduction is proportionally much less.
Hornady bullet twist discussion
 
Last edited:
Preorder available for Lapua brass

 
Cold day here in Texas, 26 deg, 29.66" Hg, DA = -1840’

Calculated 1-11" twist today at 1.535 SG shooting 62.0 gr H4350 under 208 ELD-M (MV = 2784 fps, SD = 8.1, ES = 29.5)

10 Shot group at 100 yds = 1.02 MOA. Think I'll call that good. I'll load up some more and take it out to long range later this week.

Ballistic-X-Export-2024-01-16 16:38:52.409996.jpgIMG_1474.jpeg
IMG_1480.jpeg
 
Update: Measured today’s DA = -1590’ with 16G24 winds from right.

First round hit with 1-11” twist shooting my 208 ELD-M load at 565 yards and 660 yards. 2 of 3 hits at 765 yards.

Bullet seems to be stable at distance.
 
Update: Measured today’s DA = -1590’ with 16G24 winds from right.

First round hit with 1-11” twist shooting my 208 ELD-M load at 565 yards and 660 yards. 2 of 3 hits at 765 yards.

Bullet seems to be stable at distance.

I would like to see a comparison of the wound channels between a 10" and 11". The terminal RPM apparently has an influence on how quickly the bullet comes apart/upsets. However, there's not a lot of discussion on it. Maybe it's marginal difference
 
I would like to see a comparison of the wound channels between a 10" and 11". The terminal RPM apparently has an influence on how quickly the bullet comes apart/upsets. However, there's not a lot of discussion on it. Maybe it's marginal
Bullet RPM = MV x 720 / twist (inches)

10”: RPM = 199,440

11”: RPM = 181,309

Roughly 9% difference…would be interesting to see if there is a terminal wound channel difference, but I doubt it is significant in this case
 
I would like to see a comparison of the wound channels between a 10" and 11". The terminal RPM apparently has an influence on how quickly the bullet comes apart/upsets. However, there's not a lot of discussion on it. Maybe it's marginal difference


Well I could tell you, but apparently-


@solarshooter , you could just do an open-ended search on posts by Formidilosus and decide for yourself, but I'll save you a little bit of time and let you know that you are always wrong. Always. If you don't agree, most of the time, others will jump in and tell you you are wrong. I think those that used to disagree no longer post much in this forum anymore.
 
Back
Top