Tikka 223 magazine feeding issues

[Stocky]

So mostly it seems to be people's mags just fail to have the bolt pickup the round and my problem of the tips missing the chamber and jamming is a bit unique? Put 100 rounds through the 223 this weekend and feedings pretty terrible to be honest with anything other than the long loaded 75 eld loads and even they aren't perfect. I've sold rifle for less surely there's a fix.

 

[Lawnboi]

So mostly it seems to be people's mags just fail to have the bolt pickup the round and my problem of the tips missing the chamber and jamming is a bit unique? Put 100 rounds through the 223 this weekend and feedings pretty terrible to be honest with anything other than the long loaded 75 eld loads and even they aren't perfect. I've sold rifle for less surely there's a fix.

Factory stock? Factory mags? Sounds like your mag is latching low. Confirm that your action is seated in the lug as well.

 

[Stocky]

Factory stock? Factory mags? Sounds like your mag is latching low. Confirm that your action is seated in the lug as well.

Lugs seated correctly.
I have 3 mags. A factory metal insert 4 round a factory plastic 4 round and a modified 4 round metal insert.
In a factory stock torqued to 65inch lbs.
Fails to feed due to the tip hitting below the chamber or the lip of the neck catching the chamber edge. Soft points are the worst as they hangup on the tip more often.

Best combination so far is 75 elds loaded at 2.42" in the modified magazine where the tip round seems uncontrolled for less time and the case necks have an outside chamfer.

I'll try get a video bit I'm weighing up trying to make an insert for a spare M+ magazine I have laying around to see if I can have the mag control the round a bit longer.

 

[Stocky]

OK 100% fixed any feeding issues with reloads and fixed the failure from the bullet points missing the chamber.

Compressed the spring as watching it slowly it was apparent the spring pressure was popping the rear of the case up aggressively once clear of the feed lips causing it to jump away from the bolt face and bounce around.

Now the only failure to feed is the case mouth catching the lip of the chamber. The factory Fiocchi brass is particularly shit with a decent burr around the case mouth on plenty of the cases.

Do most tikkas typically have a chamfer here?

All of my kimbers and my old how's all have a small 0.5-1mm chamfer that would solve this. An outside chamfer solves feeding and haven't been able to cause a malfunction with reloads except by short stroking the bolt and double feeding which is unavoidable.

 

[ElPollo]

Just had three 6-round Waters 223 Tikka mags delivered. Looking forward to putting them together and trying them out. It was an expensive fix for something Tikka should frankly be doing a better job on. Dave Waters was good to deal with. Getting him paid is somewhat interesting, but everything worked out and he shipped them quickly.

 

[Lawnboi]

Just had three 6-round Waters 223 Tikka mags delivered. Looking forward to putting them together and trying them out. It was an expensive fix for something Tikka should frankly be doing a better job on. Dave Waters was good to deal with. Getting him paid is somewhat interesting, but everything worked out and he shipped them quickly.

He has awesome directions on his site, I’d recommend reading them.

 

[ElPollo]

He has awesome directions on his site, I’d recommend reading them.

Directions are good. Just seems a little wonky to pay some random guy in the US by check. It worked out fine and shipped to quickly.

 

[Lawnboi]

Directions are good. Just seems a little wonky to pay some random guy in the US by check. It worked out fine and shipped to quickly.

Iv always just done PayPal.

 

[ElPollo]

Iv always just done PayPal.

I sent the check but accidentally paid him for the PayPal fee because I suck at following good directions. Told him to consider it a tip to support a small business and he should buy himself a good mid-strength beer. Instead, he threw in one of his 3d printed loading blocks. That gun was never a drop in feeder with the factory mags, but it loads slick as snot with that loading block. If his magazines work that well I’ll be tickled pink.

 

[ResearchinStuff]

My factory 4 round mag is approaching 800 rounds and had about a 50% failure to feed rate over the weekend. The 6 round with ~100 rounds on it wasn't much better. Appreciate the tips guys have shared here, going to fiddle s but before plunking down the $ for the waters mags