The 6UM

[amassi]

I’ve been curious about this too. I originally had an 18” 8tw barrel on order but ended up switching to a 7.5. I’m strongly considering running the eldm’s but don’t think they are going to hold up. I just need to pony up and buy a barrels worth of dtacs.

I have 500 I’d sell


Sent from my iPhone using Tapatalk

 

[Holt stewart]

I’ve been curious about this too. I originally had an 18” 8tw barrel on order but ended up switching to a 7.5. I’m strongly considering running the eldm’s but don’t think they are going to hold up. I just need to pony up and buy a barrels worth of dtacs.

For what it’s worth I’m shooting them (108 Eldm) out of an 18’ 7.5 twist and they’re doing great so far. I’m not stepping on it super hard, I think I’m at 3225fps and I have maybe 275-300 rounds down the tube.


Sent from my iPhone using Tapatalk

 

[omicron1792]

anyone loading ammo (commercially or custom) for the 6um? I assume unknown munitions is but I don’t see it on their site.

 

[Dhughes]

Anybody work a load with the 80gr. Eldvt? Curious for coyotes.

I ran them up to about 3750 in my 20” 6 saum. Not near as fast as I thought I could get them. I went back to the 95 tmk’s at 3660.

 

[IrkedCitizen]

anyone loading ammo (commercially or custom) for the 6um? I assume unknown munitions is but I don’t see it on their site.

There no brass yet. But they will load 6.5saum or 7 saum for you

 

[khuber84]

anyone loading ammo (commercially or custom) for the 6um? I assume unknown munitions is but I don’t see it on their site.

This is not a chambering for the non hand loader unless you have solid ties to someone in the ammo industry. Or you source all components and pay someone to assemble. Expect $4 a round.......

 

[ljones500]

I ran them up to about 3750 in my 20” 6 saum. Not near as fast as I thought I could get them. I went back to the 95 tmk’s at 3660.

What twist? No failures of the tmk’s at 3660?

 

[Tx_300wsm]

For what it’s worth I’m shooting them (108 Eldm) out of an 18’ 7.5 twist and they’re doing great so far. I’m not stepping on it super hard, I think I’m at 3225fps and I have maybe 275-300 rounds down the tube.


Sent from my iPhone using Tapatalk

N570? How many grains?

 

[Ryan Avery]

Forty-nine soldiers are prepared to go wound some elk and nilgai.

 

[khuber84]

Forty-nine soldiers are prepared to go wound some elk and nilgai.

Where did #50 go? That would drive me nuts

 

[crich]

Forty-nine soldiers are prepared to go wound some elk and nilgai.

49!? Jesus my OCD is firing on all cylinders.

 

[GoatPackr]

#50 went to science

 

[Ryan Avery]

49!? Jesus my OCD is firing on all cylinders.

******* AMP Annealer

 

[khuber84]

******* AMP Annealer

Lapua includes an extra case in every 100 round box. Wish ADG had the same generosity!

 

[Ryan Avery]

Lapua includes an extra case in every 100 round box. Wish ADG had the same generosity!

I will bring that up to them.

 

[Holt stewart]

N570? How many grains?

Actually 43 grains of H1000. This barrel hit pressure way early with everything for some reason. The last one my load was 67 grains of N570 with the 115 dtacs 30 thou off. I threw together ten loaded with 64 grains when I put this barrel on just to have a few safe rounds to run through and it started blowing primers. I ended up backing down to 62 and being not that far off the velocity from my first barrel. I think I was about 3-4 grains less H1000 in this barrel compared to the first one to be at the same speeds as well.


Sent from my iPhone using Tapatalk

 

[Holt stewart]

N570? How many grains?

I just realized that I lied about the barrel length too. This barrel is actually 20”, the last one was18”.


Sent from my iPhone using Tapatalk

 

[Ryan Avery]

From Kurt

“My son shot a buck with the 6 UM, 125 yards quartering away. Went in a few ribs back of the shoulder, found the base of the jacket nested under the offside shoulder, no exit. Typical lung damage, appeared to go through the top of the heart, found the bottom half of the heart free floating in the cavity.

It is a little tough to tell what is going with the bullet on inside on any of these animals, there has been so much damage it ends up being a coagulated mess, quite destructive.

The interesting part to me is how little blood shot meat I have ended up with, even through shoulders , especially entrance.”

 

[Dhughes]

What twist? No failures of the tmk’s at 3660?

7.5. I’ve not had any failures. I shoot 103’s at 3485 for deer. No problems there either, but they’re too hot. I just got some dtacs and matchburners in to work up for an upcoming aoudad hunt.