Sierra Heavy TMK 6MM Testing

[philcox]

Does it come up to the base of the shoulder? IIRC (probably don’t), that’s where it usually is for me

Yep, looks about there.

 

[schmidty3]

You guys suck (yet again). 6mm dies, 18" 1-7" Pbb .750 fluted barrel, and 116s when they drop are (or will be) ordered.

 

[Hurley88]

Yep, looks about there.

Yeah, then it’s not low enough case fill to be concerned about IMO. I’ve never had issue with angled shooting or erratic velocities or anything. But then again I don’t seat the bullet up the case neck, I want the whole neck grabbing the bullet.

I say rock on, I’ve gone through at least three jugs of H4350 in 243/6CM in the 41-41.5 range.

 

[nphunter]

Pretty pleased with the 107’s. Went and checked my ballistics and my drop chart is right on using sierras BC with my actual velocity.

Shot a 3”ish seven shot group at 500 and then backed up to 730 and shot three shots right at 2” holding 3/4 mil for wind, last two were 3/4” apart.

Final load:
41.5gr H4350
Peterson Brass
CCI BR2
Coal 2.918”
.022 off lands
2760fps

1:8, Tikka 16” barrel

 

[ID_Matt]

Pretty pleased with the 107’s. Went and checked my ballistics and my drop chart is right on using sierras BC with my actual velocity.

Shot a 3”ish seven shot group at 500 and then backed up to 730 and shot three shots right at 2” holding 3/4 mil for wind, last two were 3/4” apart.

Final load:
41.5gr H4350
Peterson Brass
CCI BR2
Coal 2.918”
.022 off lands
2760fps

1:8, Tikka 16” barrel

View attachment 1036600

View attachment 1036661

At 2.918” those gotta be barely in the case don’t they? I have some loaded for tomorrow. 2.785” was right about where the boat tail hits the neck/shoulder junction.

 

[nphunter]

At 2.918” those gotta be barely in the case don’t they? I have some loaded for tomorrow. 2.785” was right about where the boat tail hits the neck/shoulder junction.

I’m using M+ (6.5cm mags) they wouldn’t fit in the factory .243 M mag, the 108ELDM was right at mag length and it’s a shorter bullet.

 

[5MilesBack]

At 2.918” those gotta be barely in the case don’t they? I have some loaded for tomorrow. 2.785” was right about where the boat tail hits the neck/shoulder junction.

This one is loaded to 2.880" for a Tikka 243. You can see that the boat tail starts really close to that junction. At 2.918" his are just over 1/32" further out.....not much.

 

[ID_Matt]

I’m using M+ (6.5cm mags) they wouldn’t fit in the factory .243 M mag, the 108ELDM was right at mag length and it’s a shorter bullet.

Ahhh. I thought this was 6 creed. Ignore me!

 

[ID_Matt]

Not sure if this belongs in the other TMK thread or this one, but i got to shoot the 107’s today.

Tikka action
18” benchmark barrel spun by soldier mountain arms
Tbac Magnus suppressor
Xlr chassis

Hopefully the notes in the picture make sense. Ran a ladder with H4350 and N560 to see if I’d hit pressure and to check velocity. Never loaded 560 in this case before so wanted to try it. Decent speed but accuracy was not near as good as H4350 so i won’t pursue it any more.

It’s obvious these bullets want to shoot. Even jumping 150 thou in my chamber. 0.7” for the 7 shot ladder across 3 grains of powder and then a 3 shot group with 1 charge that was sub 0.3”. Never hit obvious pressure but i imagine it was close at 42.0.

Saved 10 at 40.5 to shoot at distance. Plate was 600 yards and wind was gusting 15-30 MPH so ignore the horizontal. About 4” of vertical roughly. BC from Sierra website just below water line.