Bore brushes?

171farm

Lil-Rokslider
Joined
Nov 3, 2020
Messages
144
What bore brushes do you all prefer? Both brand and material? I see so many varying reviews on both, Im not further ahead than I was prior to looking at them.

Also, all my other rifles I have been able to find dedicated brushes for...looking to get ones to clean my 7mm and am having issues. Several of the brands out there are for 6.5/7mm or 270/7mm...are those going to give a loose fit? Should I just get whatever brand has a dedicated sized one?
 
Joined
Apr 14, 2015
Messages
536
According to many on this forum you should never clean the bore of your rifle.
I do clean mine periodically but not much brushing. Bore jags (cotton patches) with Hoppes # 9 followed by CR10 copper cleaner and finish with another pass of Hoppes, also with a jag. I only brush when there is excessive powder or copper build up. I do buy caliber specific brushes and have always used bronze.
 
OP
1

171farm

Lil-Rokslider
Joined
Nov 3, 2020
Messages
144
According to many on this forum you should never clean the bore of your rifle.
I do clean mine periodically but not much brushing. Bore jags (cotton patches) with Hoppes # 9 followed by CR10 copper cleaner and finish with another pass of Hoppes, also with a jag. I only brush when there is excessive powder or copper build up. I do buy caliber specific brushes and have always used bronze.
Yea have also heard from many others to not clean. This is a new rifle build and the barrel break in suggestions from the builder is to do extensive cleaning for the first x number of rounds and then move to a cleaning as on necessary. Part of the reason to “break the barrel in” is to ensure cleaning is quick and easy. I know there is a camp of people that do not believe in barrel break in either. This is my first custom build so I’m going to listen to my builders advice and do it.
 
Joined
Apr 2, 2013
Messages
544
Location
Idaho
Nylon brush for me. Most everything I own now is Boretech since they won't react with their cleaners. I still have some Montana Extreme or what ever they're called.
 
Joined
Nov 12, 2020
Messages
1,342
Yea have also heard from many others to not clean. This is a new rifle build and the barrel break in suggestions from the builder is to do extensive cleaning for the first x number of rounds and then move to a cleaning as on necessary. Part of the reason to “break the barrel in” is to ensure cleaning is quick and easy. I know there is a camp of people that do not believe in barrel break in either. This is my first custom build so I’m going to listen to my builders advice and do it.
You could take 2 rifles, both from the same builder with the same components, do a break in and not do a break in and you’d never tell the difference.
 
OP
1

171farm

Lil-Rokslider
Joined
Nov 3, 2020
Messages
144
You could take 2 rifles, both from the same builder with the same components, do a break in and not do a break in and you’d never tell the difference.
I bet. The break in is really time consuming but Im going to give it a shot. I guess it cant hurt haha
 
Joined
Nov 12, 2020
Messages
1,342
I bet. The break in is really time consuming but Im going to give it a shot. I guess it cant hurt haha
It can hurt. Make sure you use bore guides and a good rod. I’d guess more barrels are ruined by the break in process than helped over crappy cleaning practices and supplies.
 
Joined
Nov 12, 2024
Messages
38
When required (hard fouling) I use bronze brushes. Don't buy those spiral things, they can't engage the crud.

Cutting is controlled tearing, doesn't matter if it is paper or steel. When you look at cut steel under magnification you will see it is not as smooth as it looks to the naked eye. If you have a cut or broached barrel it will be rougher than a button rifled barrel. Sure the makers usually lap their barrels but still they are not as "smooth as a baby's a.." That is the reason it can really pay off to do a break-in, especially if the maker says to do it. If you don't what you have is each successive bullet laying down a little gilding metal and some burnt/unburnt powder, one shot after the next in those exposed pores of the barrel. Following a break-in regimen allows each successive bullet to burnish the pores a bit eliminating the rough surface and reducing the build-up of fouling. Why do you think bores with pits lead more than those without, it is because of the open surface. Same go for nicely burnished bores versus those that are only cut and lapped.

Mike Rock used to advocate for cleaning (solvent only (Shooter's Choice/Sweets 7.62)) between each shot for the 1st 10 shots. Then between every 3 shots up to 50 total and then every 5 to a round count of 100. He believed after that every 20 rounds or so were enough. Mike made the original barrels for the Army's M24 so I suspect he knew a thing or two about cleaning. FWIW Mike also was big on using cut up paper shop towels as patches. I have tried that but I prefer regular cotton patches. I have also had good luck with spray carburetor cleaner as a solvent for both carbon and gilding metal.

I have seen some pretty rough factory barrels and advocate for doing a good break-in of those as well but first one must get all of the crap out of the barrel from factory testing/proofing. One barrel I saw on a Winchester looked like a mirror image of a rat-tail file. The gun would not group and once we got the barrel clean the reason was readily apparent.
 
Top