What do you think about the weird behaviour of my custom rifle?

[ssimo]

Yeah, cheek weld could definitely be a factor or the main one. If you have a lot of input in one position and next to none in another especially. I've gone to higher mounted scopes and hardly any contact on the comb. I think Form and others do differently so not saying it's the right or only way but I like the more upright head position and not worrying about height of comb much.

shoudn't the cheek/chin contact with the stock be useful to stabilize the system and reduce the variability caused by positional changes?

is your rufle very heavy? in which caliber is it? do also your family members have this approach to cheekweld?

 

[ssimo]

I have an X Bolt 7mm08 that shoots just OK at paper. However I have first round impacts on MOA size steel out to 910 yards consistently. So I hardly ever shoot it at paper unless to re zero or check a load. I killed a mile deer DRT at 648 this year.

Sent from my SM-S931U using Tapatalk

how is it possible that the gun is more accurate in the field than in range conditions? MOA size steel at 910 yards is very impressive, i wouldn't ever be able to hit it reliably just because of enviromentals..

 

[grfox92]

how is it possible that the gun is more accurate in the field than in range conditions? MOA size steel at 910 yards is very impressive, i wouldn't ever be able to hit it reliably just because of enviromentals..

At 910 it's because I have a good spotter calling my wind. Im good by myself out to around 600. I never said the gun was lore accurate in field conditions. The shots I am referring to are prone with a bipod or pack and rear bag.

Sent from my SM-S931U using Tapatalk

 

[wind gypsy]

shoudn't the cheek/chin contact with the stock be useful to stabilize the system and reduce the variability caused by positional changes?

Nah, i dont like using my face to stabilize a rifle. Front support, back support, and firing hand is plenty.

is your rufle very heavy? in which caliber is it? do also your family members have this approach to cheekweld?

All rifles. 223 to 300 mag sporter hunting rifles and heavy comp guns. It's common practice in competitive precision shooting circles. If you look up natural point of aim there should be some stuff from rifle kraft/chris way, frank galli, calen wojcek, Phil velayo, etc.

 

[Macintosh]

…the question is: how much shooter error gives how much shift in POI?

Form can answer directly. And there’s all sorts of opinions here. BUT I think most will agree that the more a gun recoils, the more potential poi shift is possible as a result. You already said this gun recoils significantly more than your others, ergo there is more potential for a poi shift caused by recoil management, and a greater potential shift in poi.

If you are contorting your body to see thru the scope as you said, at least for me, it makes it much harder to be consistent in my gun inputs, especially during recoil and for a subsequent shot. Try some 1/4” hard foam taped to the comb and see if it makes a difference. If it does, either lower rings or a permanent comb riser might just fix it for you. Or at least make it easier to do the practice that will fix it for you. Some of this may not be “proper” (cheek vs chin weld, depending on who you ask) but if you already have decades of muscle memory doing it one way and a pile of guns set up for that, it may be easier to run with it.

The drill mentioned earlier is helpful for seeing your field performance from various positions so that you can practice your weaknesses and see improvements, and make comparisons. Because as pointed out, range conditions are not reality. Its the “Form drill” or “hunting rifle drill”. I think of it as a field-focused version of a kraft drill. If you search it on this site you’ll find it eventually.

 

[ssimo]

Nah, i dont like using my face to stabilize a rifle. Front support, back support, and firing hand is plenty.


All rifles. 223 to 300 mag sporter hunting rifles and heavy comp guns. It's common practice in competitive precision shooting circles. If you look up natural point of aim there should be some stuff from rifle kraft/chris way, frank galli, calen wojcek, Phil velayo, etc.

so maybe i don't need a cheek rest to make my position better but i should just take some pressure off from it?
it wouldn't feel very natural tough.

i have seen different reccomendations about this, from people saying the same as you to people suggesting to rest the weight of the head on the buttstock.

How to know which is the correct way?

 

[ssimo]

At 910 it's because I have a good spotter calling my wind. Im good by myself out to around 600. I never said the gun was lore accurate in field conditions. The shots I am referring to are prone with a bipod or pack and rear bag.

Sent from my SM-S931U using Tapatalk

i was shooting pretty easily steel targets (torso sized) at 400 meters (450 yards) with my M4 with a aimpoint comp m3, after figuring out where to hold.. That's why it seems crazy that i am struggling with this rifle with all this well tought out setup, good scope, etc..
it is so frustrating not understanding what the f is happening

 

[ssimo]

Form can answer directly. And there’s all sorts of opinions here. BUT I think most will agree that the more a gun recoils, the more potential poi shift is possible as a result. You already said this gun recoils significantly more than your others, ergo there is more potential for a poi shift caused by recoil management, and a greater potential shift in poi.

If you are contorting your body to see thru the scope as you said, at least for me, it makes it much harder to be consistent in my gun inputs, especially during recoil and for a subsequent shot. Try some 1/4” hard foam taped to the comb and see if it makes a difference. If it does, either lower rings or a permanent comb riser might just fix it for you. Or at least make it easier to do the practice that will fix it for you. Some of this may not be “proper” (cheek vs chin weld, depending on who you ask) but if you already have decades of muscle memory doing it one way and a pile of guns set up for that, it may be easier to run with it.

The drill mentioned earlier is helpful for seeing your field performance from various positions so that you can practice your weaknesses and see improvements, and make comparisons. Because as pointed out, range conditions are not reality. Its the “Form drill” or “hunting rifle drill”. I think of it as a field-focused version of a kraft drill. If you search it on this site you’ll find it eventually.

interesting points. The amount of recoil could be higher due to the system being more rigid/stiff because of the carbon fiber stock and tighter tolkerances or a rifle recoil is almost exclusively dependent on load and weight of the rifle itself?

i laready tried with two socks and some duct tape and i was much more comfortable behind the rifle. I just didn't think this could make all this difference. With that rudimental setup i was leaning behind the rifle naturally with closed eyes and, when i opened my eyes, i had a good sight picture. With the current setup i end up being almost 1 cm lower than were i should to have a good sight picture when i open the eyes. This is valid if i want a cheekweld, for a chin weld (which implies neck muscles to be used to keep the head straight and less consistency on the weight applied to the stock) it is good, if i open my eyes i am on spot (this because i carefully adjusted the position of the scope to be at the right distance from my eye. The setup with the increased heught of the comb felt more natural, for sure. That said, with my old rifle i used to have a chin weld but a biut lower and i was pushing left with my head on the stock, compensating with a slight torsion with my right hand holding the grip. This worked for me for years in which i never witnessed positional induced poi shifts while training and hunting. It is also true that that rifle was shooting lower recoil rounds (308 780 m/s vs 820 m/s, both 165 grainers)

 

[thinhorn_AK]

interesting points. The amount of recoil could be higher due to the system being more rigid/stiff because of the carbon fiber stock and tighter tolkerances or a rifle recoil is almost exclusively dependent on load and weight of the rifle itself?

i laready tried with two socks and some duct tape and i was much more comfortable behind the rifle. I just didn't think this could make all this difference. With that rudimental setup i was leaning behind the rifle naturally with closed eyes and, when i opened my eyes, i had a good sight picture. With the current setup i end up being almost 1 cm lower than were i should to have a good sight picture when i open the eyes. This is valid if i want a cheekweld, for a chin weld (which implies neck muscles to be used to keep the head straight and less consistency on the weight applied to the stock) it is good, if i open my eyes i am on spot (this because i carefully adjusted the position of the scope to be at the right distance from my eye. The setup with the increased heught of the comb felt more natural, for sure. That said, with my old rifle i used to have a chin weld but a biut lower and i was pushing left with my head on the stock, compensating with a slight torsion with my right hand holding the grip. This worked for me for years in which i never witnessed positional induced poi shifts while training and hunting. It is also true that that rifle was shooting lower recoil rounds (308 780 m/s vs 820 m/s, both 165 grainers)

@BAKPAKR (sorry if it wasn’t you) made a cheek riser out of cardboard, sort of made his stock into a rokstock. He seemed to think it made a difference if I remember correctly. You could try something like that or search for his thread on that.

 

[ssimo]

@BAKPAKR (sorry if it wasn’t you) made a cheek riser out of cardboard, sort of made his stock into a rokstock. He seemed to think it made a difference if I remember correctly. You could try something like that or search for his thread on that.

i am a bit confused because many say that it is better to have a chin weld instead of a cheek weld, thus influencing less the recoil dynamic of the rifle.. so maybe i don't have a too light of a chin weld but an inconsistent one? but this way if i shoot uphill or with the bipod canted how can i "direct/control" the dynamics of recoil?