Ultralight Ultralight Rifles

[4090Sharps]

TN Arms lower budget alternative!!!

Get 'em while you can boys!

CARBON Lowers (TEGRA)

www.peacegeek.net

I picked mine up yesterday. The hole for the front takedown pin detent wasn’t fully drilled through on mine, so something to watch for. At least it was an easy fix.

 

[Good Stuff]

I'm slowly reading through all the pages here with plans to build a ULUL 223. Since I can't get a Shaw barrel, what is the recommended barrel now?

 

[gtriple]

I'm slowly reading through all the pages here with plans to build a ULUL 223. Since I can't get a Shaw barrel, what is the recommended barrel now?

Have you tried contacting Shaw to see if they can make one?

If they aren’t going to, the Faxon pencil match barrel I had was extremely accurate. Just gotta plug the gas port.

 

[Good Stuff]

Have you tried contacting Shaw to see if they can make one?

If they aren’t going to, the Faxon pencil match barrel I had was extremely accurate. Just gotta plug the gas port.

No. I didn't think Shaw would do it.

 

[Thegman]

No. I didn't think Shaw would do it.

I would check with Shaw. Says temporarily unavailable, I would assume they just sold out of the last batch. If they know there's interest they'll likely do another run I'd imagine.

 

[ztc92]

I'm slowly reading through all the pages here with plans to build a ULUL 223. Since I can't get a Shaw barrel, what is the recommended barrel now?

PM sent as I have one I’m not using.

 

[robtattoo]

If you feel like upsizing, I've got everything you need to start shooting .300Ham'r.
Barrel, brass, bullets & dies.

 

[C Bow]

X Cal

 

[Hoosker Doo]

I forgot to bring the rifle up front for a picture, but I christened my ULUL 6x45 with its first kill last night. You can see it in the background. 300 yards, DRT. (Deer on the left)

 

[Good Stuff]

Congratulations! I'm waiting on parts to finish my build.

 

[Thegman]

I forgot to bring the rifle up front for a picture, but I christened my ULUL 6x45 with its first kill last night. You can see it in the background. 300 yards, DRT. (Deer on the left)

View attachment 948430

Nice! What bullet did you use and how did it perform? (Obviously killed well, just wondering about penetration, exit size, if any, etc).

Never mind, I see you put it in the 6mm thread!

 

[Hoosker Doo]

Nice! What bullet did you use and how did it perform? (Obviously killed well, just wondering about penetration, exit size, if any, etc).

Never mind, I see you put it in the 6mm thread!

Yeah, it's in the 6mm thread

https://rokslide.com/forums/threads/6mm-243-hunting-success-on-big-game.284525/post-4364997

But for those curious, 16" X-caliber has the 90 gr ELD-X going 2,504 fps. So at 300 I was around 2,025 fps. Passed through quartered away from flank to behind front shoulder, just below the spine. Dropped immediately and never moved.

 

[robtattoo]

Well, this was a little underwhelming

I was expecting another couple hundy on those numbers.

I fired my first 50 shots with the 6x45 barrel today (the chrono group was 31-40). Averaging 2-ish inch groups. Not terrible, but not impressive, either.
I was consistently 10/10 on a 4" gong at 500 with my 7lb Tikka. 223, so I'm pretty sure it ain't me (although the lighter the rifle, the tougher I find it to shoot will, so it could've been....)
I'd be happy hunting with it inside of 200yds, as it sits & I'm sure that a couple of hundred more through the pipe will help tighten it up a bit!

 

[JBradley500]

Well at least your penmanship is immaculate.

What is the minimum impact velocity for that bullet?

 

[Thegman]

Well at least your penmanship is immaculate.

What is the minimum impact velocity for that bullet?

Hornady told me 1,400, maybe down to 1,300 for that bullet. One of our resident 6x45 experts said 1,200 or even a bit lower. Sounds like 1,400 would be pretty safe.