Ultralight Ultralight Rifles

[Dukhtr3]

Well I got my rifle together and tried to go shoot it, but it's not feeding or shooting properly.

Feeding - it gets stuck about a CM after engaging the back of the casing. Won't push it up thru the feed ramp. I'm having to drop a round into the barrel to load.

Shooting - the bolt will not go all the way forward with a round chambered. It gets stopped a few mm from the end. Then when you pull the trigger, the trigger goes off, but the firing pin doesn't strike the primer at all.

Do the bolt or the bolt internals need to be lubed/greased?

I just put mine together and went to shoot today and I also had the same problem with the shooting. I could only get a few rounds to shoot. I thought it may be my lower but I didn't have another with me to try. I was also getting no primer strike too. I doubt it's the lower but I want to try a different lower to confirm.

Sent from my Pixel 7 Pro using Tapatalk

 

[Thegman]

I was trying to shoot some factory 55gr ball ammo and black hills 77gr tmk, so that's probably not the issue. I managed it get a couple to shoot, but couldn't reproduce it consistently.

So for the feeding, did you remove the barrel from the upper or do it while attached?

Yes, remove the barrel from the upper.

Are you using the bolt that came with the solo? I'm wondering if you’re getting stuck pushing the extractor over the rim? If it's a solo bolt they should have already removed the o-ring and rubber plunger to make that easier. I can only think of that or too little headspace.

What happens if you place a round or piece of brass in the chamber and slap the bolt forward? Does it go into battery, and if so, is extraction easy?

If headspace is too tight it will probably be difficult to extract. If it extracts easily, it's likely something with your extractor.

 

[Thegman]

I just put mine together and went to shoot today and I also had the same problem with the shooting. I could only get a few rounds to shoot. I thought it may be my lower but I didn't have another with me to try. I was also getting no primer strike too. I doubt it's the lower but I want to try a different lower to confirm.

Sent from my Pixel 7 Pro using Tapatalk

No primer strike is likely from not being fully in battery. I'm not sure why that would be happening though.

 

[gtriple]

I just put mine together and went to shoot today and I also had the same problem with the shooting. I could only get a few rounds to shoot. I thought it may be my lower but I didn't have another with me to try. I was also getting no primer strike too. I doubt it's the lower but I want to try a different lower to confirm.

Sent from my Pixel 7 Pro using Tapatalk

Is yours getting stuck in the same spot as mine?

Which barrel do you haveM

 

[Dukhtr3]

Is yours getting stuck in the same spot as mine?

Which barrel do you haveM

I am not sure how far it was stuck open. I loaded it on the bench and It is completely closing but I won't be able to shoot until next weekend. I was shooting reloads so I will also have to bring some factory ammo to try. I am running the bear creak barrel.

Sent from my Pixel 7 Pro using Tapatalk

 

[Taudisio]

I remember having to be really rough with mine at first as well. Both rifles definitely loosened up over time. AR’s can be so hard to diagnose over the internet. I would just blast 55gr bullets for the first 50 or so and be really forceful with the rifle to see if that helps. Sounds it could be a mag problem as well, and/or extractor like said above.

 

[Sadler]

This one is a little heavier at 4lbs 12oz but have any of you guys shot one of these? I’m wanting a lightweight 6ARC SBR/Pistol and this is the lightest one I’ve found.

Paladin 6mm Arc AR15 - GQ Armory

Details The Paladin 6mm Arc AR15: Long distance shooting meets CQB How does a thousand yard AR15 that weighs less than 5 lbs sound? The Paladin 6mm Arc AR15 is a rifle for those who want to shoot far without the size and weight of conventional long range rifles. 6mm Arc, a cartridge created by...

gqarmory.com

 

[The Guide]

This one is a little heavier at 4lbs 12oz but have any of you guys shot one of these? I’m wanting a lightweight 6ARC SBR/Pistol and this is the lightest one I’ve found.

$3k is a little tough to swallow unless it ran flawlessly with a suppressor and without. Personality I'd do a 16" 6GT Ultra Light Tikka build before I fussed with that gun.

Jay

 

[Solm]

Sako carbonlight, 5 lb 3 oz, incredible rifle but expensive

 

[gtriple]

Sako carbonlight, 5 lb 3 oz, incredible rifle but expensive

That's light, but not really ultralight. These rifles are sub 5 lbs scoped and loaded.

 

[The Guide]

Got my Shaw barrel in today. Put it on the SOLO upper and put the upper into my AR pistol lower. Looks and works pretty good. Need to find a hand guard but I really like the look of it without one.

Jay

 

[Lentuk]

My Shaw came in today, just waiting on two more parts.

 

[doverpack12]

My Shaw came today as well. Still waiting on the handguard so couldn’t assemble.

Bear creek barrel is a bit lighter. Probably a wash or little heavier with lightweight backward gas block.

 

[Lando]

Okay, I bought the Shaw Barrel in 223 Wylde. I don't have anything else. What lower and upper should I buy? Handguard? Stock? Parts to build handguard and stock?

Is this a decent trigger for the $?

PSA Custom AR Trigger Single-Stage Flat Drop-In Match Grade - 116055

Platform: AR Trigger Type: Flat Pull Weight: 3.5 lbs. Pull Type: Single-Stage Housing Material: 7075-T6 Aluminum Finish: Black

palmettostatearmory.com

 

[BLJ]

@doverpack12.
How did the Bear Creek shoot? I’ve thought about a side charger in one of these as a starting point. Thanks.

 

[gtriple]

Okay, I bought the Shaw Barrel in 223 Wylde. I don't have anything else. What lower and upper should I buy? Handguard? Stock? Parts to build handguard and stock?

Is this a decent trigger for the $?

PSA Custom AR Trigger Single-Stage Flat Drop-In Match Grade - 116055

Platform: AR Trigger Type: Flat Pull Weight: 3.5 lbs. Pull Type: Single-Stage Housing Material: 7075-T6 Aluminum Finish: Black

palmettostatearmory.com

Upper:

Gen II Solo 300 upper (no barrel)

• Manually operated, straight pull • Stainless steel bolt handle • Includes bolt carrier assembly • 5.56/300 Blk sized bolt head • Mil-spec Ejection Port Cover • Accepts AR-15 barrel extensions • Weight: 12oz

solo300.com

Lower:

Tennessee Arms Company, LLC/TNARMS-15 Carbon Fiber

Lighter Stronger and Unreal Performance this AR15 Stripped Receiver is our best yet

www.tnarmsco.com

Lower parts kit:

Lightweight Polymer LPK

Upgrade your AR-15 with the New Frontier Armory Polymer LPK. Complete your lower receiver build with this lightweight and reliable polymer parts kit. Made in the USA.

www.newfrontierarmory.com

Buffer tube:

AR-15 / LR-308 A2 STANDARD RIFLE BUFFER TUBE

AR-15 / LR-308 A2 Standard Rifle Buffer Tube - Reliable and Secure Attachment for Your Firearm's Stock.

kakindustry.com

Stock:

AR15 Ultralight Stock

Weighs only 4 ounces with buffer tube! This is 3D printed in a modified polycarbonate. Comes with 1/4-28 securing screw and 4-40 set screw. This stock wi...

farrow.tech

Upgraded grip (optional):

15° Vertical Polymer - Grips - AR-15 & M16 - Tactical Rifles - Products

Hogue, Inc

www.hogueinc.com

Handguard options:

NFA Gen 2 Hand Guards

Upgrade your firearm with the high-quality NFA Gen 2 Hand Guards. Made in the USA from lightweight aluminum, these MLOK compatible hand guards are durable and easy to install.

www.newfrontierarmory.com

Ultralight AR-15 Handguard System – JAG Composites

There's a couple of simple tube handguards in this thread that others could recommend.

 

[Ferrulewax]

Anyone care to tell me what the solo uppers are now? I should have bought one last spring when they were cheap and available

 

[gtriple]

Anyone care to tell me what the solo uppers are now? I should have bought one last spring when they were cheap and available

My solo300 upper with cerakoted bolt handle was $344 shipped.

 

[Ferrulewax]

My solo300 upper with cerakoted bolt handle was $344 shipped.

Barreled? Sounds like he had raised the price pretty significantly either way.

 

[gtriple]

Barreled? Sounds like he had raised the price pretty significantly either way.

No. I think it's a fair price because the new ones are definitely more expensive to make.