Thoughts on a tikka build idea I am tossing around

[270quest]

I reached out to Karl, waiting to see his response, but figured I would pose this question here.

I am thinking of retiring/refreshing the Tikka 7 rem mag. Retiring as in barreling it with a feather lite contour carbon barrel from Carbon Six that finishes at .750 and rechamber for 7 PRC at 22", threaded for a suppressor. - Pretty strait forward.

The hold up is it sets in a Standard Fill McMillan Sako Classic stock. Per McMillan, that stock can be modified to hold up to a #4 Douglas barrel blank. I really don't' want to have to buy a new stock if at all possible. Do you think its feasible to fit this barrel into this McMillan stock?

Otherwise, I may have to look at getting a new McMillan stock to accommodate that larger barrel - probably a Game Hunter.

 

[pods8 (Rugged Stitching)]

IMHO, ditch the carbon barrel, figure out what steel contour fits reasonably and go with that. Also go shorter unless you have already hunted with a 22" barrel and suppressor and don't mind. The kids 243win is threaded at 22" and is far more annoying than a 18-19" barrel with a can on it.

 

[wind gypsy]

IMHO, ditch the carbon barrel, figure out what steel contour fits reasonably and go with that. Also go shorter unless you have already hunted with a 22" barrel and suppressor and don't mind. The kids 243win is threaded at 22" and is far more annoying than a 18-19" barrel with a can on it.

^This. If you like the existing stock buying a whole new stock in addition to the upcharge for carbon over a steel barrel is insanity. I'd just get a steel tube close to the original contour and roll on.

 

[amassi]

Douglas #4 is a fairly stout steel contour
I’d drop down to a 3 or 3b or taperless .750
All would be drop in for your stock, have adequate clearance and take any threading you may want.


Sent from my iPhone using Tapatalk

 

[270quest]

IMHO, ditch the carbon barrel, figure out what steel contour fits reasonably and go with that. Also go shorter unless you have already hunted with a 22" barrel and suppressor and don't mind. The kids 243win is threaded at 22" and is far more annoying than a 18-19" barrel with a can on it.

I will be running a 6" can, and ran my sons rifle at 21" and it seemed like a good match. I might consider going to 20" barrel. Have ran steel all my life, want to play with a carbon on this one.

 

[wind gypsy]

Douglas #4 is a fairly stout steel contour
I’d drop down to a 3 or 3b or taperless .750
All would be drop in for your stock, have adequate clearance and take any threading you may want.

I dont think douglas #4 is that stout. Finish at 0.650 @26" but seen to go down pretty quickly on the breech end. Smaller than a #3 bartlein for sure.

 

[pods8 (Rugged Stitching)]

I will be running a 6" can, and ran my sons rifle at 21" and it seemed like a good match. I might consider going to 20" barrel. Have ran steel all my life, want to play with a carbon on this one.

Its your money, I have a carbon 24" 300wsm which I went carbon at the time for a stiffer barrel at that length. Been there/done that and when going shorter barrel I have zero interest in spending the extra money for no gain (other than if that aesthetic is worth it to you) and sometimes its a detraction (some carbon barrels get wonky as they heat up).

I notice a different handling the 22" versus my 19" both in the field and when in/out of vehicles, both fit my gun case still with a can on, but the 22" doesn't fit my safe as well.

 

[wind gypsy]

I will be running a 6" can, and ran my sons rifle at 21" and it seemed like a good match. I might consider going to 20" barrel. Have ran steel all my life, want to play with a carbon on this one.

If it appeals to you, to each his own. Hopefully someone can confirm your existing stock can be hogged out to fit the featherweight contour. An entirely new micky stock and bedding it is a pretty significant price on top of the hundreds extra for a blank just to have a McGowan with some carbon glued onto it though.