The All New MRC/S2H Marshall Rifle Now Available

[BLJ]

There was this…

I don't want to speak out of turn. Can't find if it was discussed earlier in the thread, UM barreled this particular rifle, beyond that I don't know specifics.

Then this…

UM isn’t supplying anything. The answer was already given- but I suppose that’s too easy.

and this….

And they’re not going to tell you. It isn’t just one. Right now there are Marshals with MRC, Brux, Lilja, ACE, and others. I’m sure if they can they will settle on one or two, but it won’t matter- the rifles will shoot as they should.

Looks like @Bluumoon got a good barrel.

@BAKPAKR

 

[Formidilosus]

@Formidilosus, I went back to find the answer to my UM re-barrel question so I wouldn’t lose sleep tonight worrying about it. It appears that a couple other people had the same question and, in post 709, @Bluumoon said, “Can't find if it was discussed earlier in the thread, UM barreled this particular rifle, beyond that I don't know specifics.”

Was his rifle re-barreled by UM, and, if it was, can you point me (and possibly @Bluumoon) to the post that explains why it was?

You can’t find where the MRC rep stated that they are not using their own barrels anymore, and are using quality barrels from outside barrel makers? And then where I wrote quite a few barrels that have already been used?

I’m not sure what you are trying to get out of it, but most of your posts with regards to this rifle have the same, near trolling odd bent to them. You normally do not post like this.

 

[BAKPAKR]

You can’t find where the MRC rep stated that they are not using their own barrels anymore, and are using quality barrels from outside barrel makers? And then where I wrote quite a few barrels that have already been used?

I’m not sure what you are trying to get out of it, but most of your posts with regards to this rifle have the same, near trolling odd bent to them. You normally do not post like this.

I did not ask who made the barrel — I asked if UM barreled @Bluumoon’s rifle, as he said they did, and, if so, why?

I have a Remington 700 that was barreled by Jon Beanland. When I tell people how well it shoots, I commend Beanland, not Remington.

 

[Bluumoon]

I did not ask who made the barrel — I asked if UM barreled @Bluumoon’s rifle, as he said they did, and, if so, why?

I have a Remington 700 that was barreled by Jon Beanland. When I tell people how well it shoots, I commend Beanland, not Remington.

Being that these are being sent out w a 10 round guarantee (unlike pretty much anything else out there) I don’t see the concern.

Also, you are obviously overlooking my extraordinary shooting and reloading abilities to achieve results like these . Kidding, if anything I have a special ability to muck stuff up and break things unintentionally.

 

[2Stamp]

@Formidilosus @Imac45acp Any updates on the further testing of the new barrels?

 

[Bluumoon]

Was thinking I might sell the 95gr TMKs I had on hand based on how they did in my Tikka, may have to hold off.. The 1st 4 were touching, good bit of mirage after that.

 

[Gstew1930]

Was thinking I might sell the 95gr TMKs I had on hand based on how they did in my Tikka, may have to hold off.. The 1st 4 were touching, good bit of mirage after that.

Let me know when you're ready to sell that rifle lol

 

[2Stamp]

@Formidilosus @Imac45acp any updates? How are the rest of these coming?

 

[Formidilosus]

@Formidilosus @Imac45acp any updates? How are the rest of these coming?

Two more are shipping tomorrow or Monday.

#227




#236

 

[RancherJohn]

I got some time today to pick my Marshall up and do a little bit of shooting. First impressions on the rifle are very good, fit and finish is on par with what I was expecting. Action screws are paint-penned, magazines had stickers denoting a matching SN to the rifle. Barrel channel is properly opened up, pictured next to a factory T3X .223 barrel in a sendero profiled channel. I have a LOP kit here to install at some point as well, unless @atmat wants to come up and get a second crack at one. Scope is a RS1.2 in low Hawkins rings, OG6.5 can. Other rifle is a Tikka .223, 16" barrel with 6" can.

I did a rough zero with some Hornady 87 gr VMAX, then 10 rds of Berger 105 gr Hybrid Target (~1.1 MOA), 10 rds of ELDM (~1.3 MOA), and 10 rds ELDX (~1.2 MOA); all factory loads. ELDMs are the only load I got a velocity on, avg 2840 fps at 8000'. I have some Hornady 105 gr BTHP on hand as well, and should get a chance to shoot more groups with the rifle this weekend to see if I can bring the sizes down a tenth or two, and to true it at distance.

 

[Gstew1930]

I got some time today to pick my Marshall up and do a little bit of shooting. First impressions on the rifle are very good, fit and finish is on par with what I was expecting. Action screws are paint-penned, magazines had stickers denoting a matching SN to the rifle. Barrel channel is properly opened up, pictured next to a factory T3X .223 barrel in a sendero profiled channel. I have a LOP kit here to install at some point as well, unless @atmat wants to come up and get a second crack at one. Scope is a RS1.2 in low Hawkins rings, OG6.5 can. Other rifle is a Tikka .223, 16" barrel with 6" can.

I did a rough zero with some Hornady 87 gr VMAX, then 10 rds of Berger 105 gr Hybrid Target (~1.1 MOA), 10 rds of ELDM (~1.3 MOA), and 10 rds ELDX (~1.2 MOA); all factory loads. ELDMs are the only load I got a velocity on, avg 2840 fps at 8000'. I have some Hornady 105 gr BTHP on hand as well, and should get a chance to shoot more groups with the rifle this weekend to see if I can bring the sizes down a tenth or two, and to true it at distance.

View attachment 1008728

View attachment 1008731

View attachment 1008730

Good looking rifles there bud

 

[ztc92]

I got some time today to pick my Marshall up and do a little bit of shooting. First impressions on the rifle are very good, fit and finish is on par with what I was expecting. Action screws are paint-penned, magazines had stickers denoting a matching SN to the rifle. Barrel channel is properly opened up, pictured next to a factory T3X .223 barrel in a sendero profiled channel. I have a LOP kit here to install at some point as well, unless @atmat wants to come up and get a second crack at one. Scope is a RS1.2 in low Hawkins rings, OG6.5 can. Other rifle is a Tikka .223, 16" barrel with 6" can.

I did a rough zero with some Hornady 87 gr VMAX, then 10 rds of Berger 105 gr Hybrid Target (~1.1 MOA), 10 rds of ELDM (~1.3 MOA), and 10 rds ELDX (~1.2 MOA); all factory loads. ELDMs are the only load I got a velocity on, avg 2840 fps at 8000'. I have some Hornady 105 gr BTHP on hand as well, and should get a chance to shoot more groups with the rifle this weekend to see if I can bring the sizes down a tenth or two, and to true it at distance.

View attachment 1008728

View attachment 1008731

View attachment 1008730

Love the custom paint job on the 223, I may need to try something like that on mine this winter when I get bored. Is it just spray paint?

Also does your rokstok on the 223 have the grip panels on the butt stock, same as the lites? I didn’t know that was an option on full sized Rokstoks, it looks great!

 

[RancherJohn]

Love the custom paint job on the 223, I may need to try something like that on mine this winter when I get bored. Is it just spray paint?

Also does your rokstok on the 223 have the grip panels on the butt stock, same as the lites? I didn’t know that was an option on full sized Rokstoks, it looks great!

Yeah it's just spray paint, I used some shredded cardboard shipping filler as a variable stencil. Makes it very quick to create a 'random' pattern. The texture on the stock is textured spray paint, just used masking tape and a 20 ga shotgun shell to layout the radiused ends, then a light coat of texture & sponge to break it up. I'll get around to adding it to the Marshall Rokstok soon, it makes a noticeable difference shooting with gloves.

 

[Ajsomp]

Yeah it's just spray paint, I used some shredded cardboard shipping filler as a variable stencil. Makes it very quick to create a 'random' pattern. The texture on the stock is textured spray paint, just used masking tape and a 20 ga shotgun shell to layout the radiused ends, then a light coat of texture & sponge to break it up. I'll get around to adding it to the Marshall Rokstok soon, it makes a noticeable difference shooting with gloves.

View attachment 1008759

That stock is looking good with that 223. Still my favorite sponge pattern

 

[RancherJohn]

That stock is looking good with that 223. Still my favorite sponge pattern

Agreed! It has ended up being the perfect stock setup & pattern for how I'm using it, thanks again.

 

[RockAndSage]

Yeah it's just spray paint, I used some shredded cardboard shipping filler as a variable stencil. Makes it very quick to create a 'random' pattern. The texture on the stock is textured spray paint, just used masking tape and a 20 ga shotgun shell to layout the radiused ends, then a light coat of texture & sponge to break it up. I'll get around to adding it to the Marshall Rokstok soon, it makes a noticeable difference shooting with gloves.

View attachment 1008759

Would you mind documenting this next one, and putting it up as a separate thread? Looks like a solid process.