The 22 creedmoor thread

khuber84

WKR
Joined
Jun 6, 2019
Messages
1,671
77tmk has only 0.030 less bearing than the 88. My next barrel will be throated accordingly. This is the dummy I'm sending my smith to throat for touch. It's a bit ahead the neck shoulder junction for some seating tunage.
20240808_202005.jpg
Anyone regretted throating their barrel for 88s at a longer coal? Say around 2.75ish to keep the boat tail just above the shoulder-neck junction.
 

Stocky

Lil-Rokslider
Joined
May 8, 2019
Messages
166
77tmk has only 0.030 less bearing than the 88. My next barrel will be throated accordingly. This is the dummy I'm sending my smith to throat for touch. It's a bit ahead the neck shoulder junction for some seating tunage.
View attachment 747755
Base to ogive on the 75 eld is .102" shorter than the 88. Boattail seems the same length or is damn close. That the 88 you have in the picture? I thought I was seated long at 2.75" I'll just send that away and have it chambered.
 

khuber84

WKR
Joined
Jun 6, 2019
Messages
1,671
Base to ogive on the 75 eld is .102" shorter than the 88. Boattail seems the same length or is damn close. That the 88 you have in the picture? I thought I was seated long at 2.75" I'll just send that away and have it chambered.
Yes that's an 88. The boat tails on the 75, 80 and 88 are all pretty close. The 80/88 nose are close, it's all in the bearing surface.
 

mxgsfmdpx

WKR
Joined
Oct 22, 2019
Messages
5,970
Location
Outside
Two questions if folks don't mind...

What are we seeing for barrel life on average with "conservative-ish" 80 ELDM and 77TMK loads?

What are we seeing for rough yardage if a guy wanted to stay over 1,750ish impact velocity? Let's say an 18" barrel.
 

T_Widdy

Lil-Rokslider
Shoot2HuntU
Joined
Nov 24, 2023
Messages
213
Location
Wyoming
What are we seeing for rough yardage if a guy wanted to stay over 1,750ish impact velocity? Let's say an 18" barrel.
18” tikka 22-250 reamed to 22 creed
80eldm-3125 fps mv
900yd- 1804 fps

77tmk-3200fps mv
800yd-1782 fps

I don’t know about barrel life yet but I don’t care, this is my new favorite caliber and will chamber another when this one is done
 

mxgsfmdpx

WKR
Joined
Oct 22, 2019
Messages
5,970
Location
Outside
18” tikka 22-250 reamed to 22 creed
80eldm-3125 fps mv
900yd- 1804 fps

77tmk-3200fps mv
800yd-1782 fps

I don’t know about barrel life yet but I don’t care, this is my new favorite caliber and will chamber another when this one is done
Heck yeah! I would also just spin another barrel on, but I shot 500 rounds of .223 77 TMK just this morning...
 
Joined
Jun 7, 2023
Messages
672
Location
Wyoming
I too have joined the ranks of 22 Creed. I just pulled the 6.5 PRC barrel from my Zermatt TL3 and added a 20-inch PROOF barrel in 22 CM. Haven't shot it yet, but I'm looking forward to busting a deer or antelope with this combo. Last week, I was shooting a Horizon Firearms 22 Creed out to 650. This cartridge is a beast.
 

T_Widdy

Lil-Rokslider
Shoot2HuntU
Joined
Nov 24, 2023
Messages
213
Location
Wyoming
Heck yeah! I would also just spin another barrel on, but I shot 500 rounds of .223 77 TMK just this morning...
Ive had mine a month and have around 450 through it, I hope I don’t shoot it out before my deer hunt but it’s just so sweet to shoot! Can spot almost every impact and it’s quiet with a can. It’s almost identical to shoot compared to my 223, just more power!
 

Gstew1930

Lil-Rokslider
Classified Approved
Joined
Jan 28, 2023
Messages
251
18” tikka 22-250 reamed to 22 creed
80eldm-3125 fps mv
900yd- 1804 fps

77tmk-3200fps mv
800yd-1782 fps

I don’t know about barrel life yet but I don’t care, this is my new favorite caliber and will chamber another when this one is done
Agreed! its to fun not to shoot
 
Joined
Sep 6, 2023
Messages
96
About to order a barrel in .22cm. If I’m wanting to shoot 80 & 88gr Eldm’s, what twist rate would be best? Thinking about a 22” or 24” barrel. I’m at 1000’ asl.
 

ChrisAU

WKR
Joined
Jan 12, 2018
Messages
6,731
Location
SE Alabama
My 16.5" 1-8 twist will be put together by the end of this week, very excited to shoot it this weekend. With the slower speed's I'll get from the shorty barrel think I'll have trouble stabilizing an 88 ELD-M?

I'm not a reloader yet, I have a case of factory Hornady 80 ELDM and a box each of Copper Creek 75gr ELDM, 80 gr ELDX, and 88 gr ELDM.
 

Avonac

Lil-Rokslider
Joined
Oct 17, 2014
Messages
127
If you are wanting to build one off of a slow twist Tikka 22-250, can I buy a take off 8twist .223 barrel and have it chambered and swapped?
In my mind I think it should be fine. Just wanted a second opinion.
 

Stocky

Lil-Rokslider
Joined
May 8, 2019
Messages
166
Thanks! Not sure I can specify a bore diameter with criterion.
Well if they only make a 218 bore get another barrel.

Edit: maybe that's a bit harsh but a tighter bore will increase the likelihood of blowing up bullets. A mate here with a 22-250 in an 8 twist was blowing up 77 tmks running well below creedmoor velocities and the tmk have a thicker jacket.
 
Joined
Sep 30, 2017
Messages
908
Forgot to post the final product but she’s all done for now my 22 creed all dialed in ready to head to az this December

92560ecd7074849f55f8cc75e1894c4f.jpg



Sent from my iPhone using Tapatalk
 
Joined
Oct 6, 2014
Messages
1,905
Location
Wasilla, Alaska
@Formidilosus and anyone else with experience with both 22 and 6 CM;

A lot of people are choosing the 22 CM for 0-600 hunting ranges, though the ballistics carry 1800 fps out to a lot further than that.

Say you want your effective range to be 900 yards on game and you practice to 1200 regularly on steel & rocks. Both cartridges carry sufficient velocity for both those purposes. Would there be any reason to choose 6 mm rather than 22 for any particular reason, ie Splash size, wound cavity size etc.?

(22 cm w/ 80 & 88’s, 6 CM w/ 108-115g)
 

ChrisAU

WKR
Joined
Jan 12, 2018
Messages
6,731
Location
SE Alabama
@Formidilosus and anyone else with experience with both 22 and 6 CM;

A lot of people are choosing the 22 CM for 0-600 hunting ranges, though the ballistics carry 1800 fps out to a lot further than that.

Say you want your effective range to be 900 yards on game and you practice to 1200 regularly on steel & rocks. Both cartridges carry sufficient velocity for both those purposes. Would there be any reason to choose 6 mm rather than 22 for any particular reason, ie Splash size, wound cavity size etc.?

(22 cm w/ 80 & 88’s, 6 CM w/ 108-115g)

One particular reason I’m building both is legality in a few states. Very interested to hear @Formidilosus opinion on your question though.
 
Top