SilencerCo Scythe Ti failures

[BjornF16]

If you’ve experienced catastrophic failure of the Scythe Ti, please post the following:

1. Cartridge or cartridges used with approximate round count

2. Barrel length

3. Factory ammo, hand loads or both

4. Details of ammunition

5. Details of failure (to include failure point and pics)

 

[bearcreekbandit]

If you’ve explained catastrophic failure of the Scythe Ti, please post the following:

1. Cartridge or cartridges used with approximate round count

2. Barrel length

3. Factory ammo, hand loads or both

4. Details of ammunition

5. Details of failure

1. Cartridge: .300 PRC (approximately 3,000 rounds of 6.5 CM and .308 Win, 200 7mm PRC)
2. Barrel Length: 20 inches
3. Factory Ammo
4: Ammo: Hornady Precision Hunter 212-grain ELD-X
5. Weld failure at second weld from rear. Front end of can separated and flew 50 yards down range. No baffle or endcap strikes, bullet impact was consistent with rest of the group. Failure occured after 15 rounds of .300 PRC.

 

[mt100gr.]

1. Cartridge: .300 PRC (approximately 3,000 rounds of 6.5 CM and .308 Win, 200 7mm PRC)
2. Barrel Length: 20 inches
3. Factory Ammo
4: Ammo: Hornady Precision Hunter 212-grain ELD-X
5. Weld failure at second weld from rear. Front end of can separated and flew 50 yards down range. No baffle or endcap strikes, bullet impact was consistent with rest of the group. Failure occured after 15 rounds of .300 PRC.

You need to throw up a "yes" in the poll!

 

[mlevimadden]

I voted no but only have 200 rds of 6.5 PRC on a 20" barrel through my scythe.

 

[HighUintas]

I voted no with low round count also.

Change your vote later if your can separates.

 

[B_Reynolds_AK]

Tyler Freel up here in Alaska had one fail. I don’t think he frequents here, so wanted to add it to the list.

 

[wind gypsy]

Tyler Freel up here in Alaska had one fail. I don’t think he frequents here, so wanted to add it to the list.

@bearcreekbandit is Tyler.

 

[Fever Buck]

Is there a known failure issue with these?

 

[bergie]

Well I got mine in last week. Guess I will follow this thread, so far so good for me but 7 shots isn't even enough for me to vote.

 

[Harvey_NW]

Is there a known failure issue with these?

Not exactly sure where the first one is, but seems like there are 5 or 6 reported from here through current in this thread.

Silencerco Scythe TI review

Two failures mentioned in 694 posts does seem a bit concerning. Not sure what an acceptable failure rate is for something like this. Sent from my iPhone using Tapatalk I would think close to zero. a supressor is a hearing protection device. Of course I shouldn’t pull the trigger after the...

rokslide.com

 

[BjornF16]

Voted no, only have a few hundred rounds of 6XC (22” barrel) through it though

 

[WyldGoose]

Voted no.
Shooting an 18” 6 cm with the 5.56 flat cap from Hansohn Bros.
Only have 150 rounds on it so far…

 

[Ryan Avery]

I have over 3000 rounds on mine. Most of the shots are from a .223, but it has over 500 shots from a 20" 6UM, another 50ish from a 16.5" 6UM, and 300ish from a 20" 6.5 PRC.

 

[HighUintas]

My NO is compromised of about 300ish rounds. A mix of a 21" 6.5cm running a moderate load, maybe 50 rounds, and a 22" 243 running hot loads for about 250ish rounds.

 

[Raghornklr]

Voted yes, I'll put up the same info as other thread
1. 6.8 western 500+ rounds
2. 20"
3. Hand loads
4. 175tgk pushed by H-1000
5. Separated at second weld.

 

[TxLite]

No (not yet??)
500ish rounds consisting of 12” 556, 18” 7prc, 18” 22-250, 16” 556, 16” 6 arc and a little bit of 10.5” 300blk.

Probably close to 40-50% of that is the 18” 7prc with a stout load of N570.

 

[BlueJay]

No for me, about 300 rounds with a 20" 6 ARC, shooting factory 108 ELDM.

 

[Tahoe1305]

Also a no. ~100 rounds of 20-24” 6.5C but then ~100 rounds of 20” 7 wsm

 

[northernlandgar]

Another no, though the can is fairly new. I have 147 rounds of 6.5CM through it without issue. Barrel is 20" long.

 

[lager]

A no for me , but my brother had one come apart last wekend. Probably only 2-300 rounds fired. Looked the one in the picture. Must be a weld issue on some.