Show your Tikka ten round groups

[The Harbor Master]

A Superlite 7 Mag is not going to be easy to shoot little bug hole groups. 1” 10 round group is excellent. You got your load.

I think so too, and thank you. It's a heck of thump, and my first magnum so I'm definitely humbled.

 

[General RE LEE]

I think so too, and thank you. It's a heck of thump, and my first magnum so I'm definitely humbled.

I had a Tikka Superlite 30-06. With 178 ELDX handloads, it kicked as harder or maybe even harder than a 10 lb 300 win mag. When I was doing load development, I had to work much harder on form than a light kicker.

 

[wyosam]

Here’s 21 (might have been 24?) at 100. Barrel had been off this action since last winter, cleaned with storage oil in it. Pushed a dry patch through it, screwed it on, dialed it down the 0.6 my notes said worked last time. Factory 6.5cm barrel from a donor action. Spartan bipod/rear bag from a wood bench.

Sent from my iPhone using Tapatalk

 

[northernlandgar]

Here's a group with a question.

Fired ten rounds from my T3x in 6.5CM into a little less than 0.7" inches yesterday.
I'm shooting a 140gr Sierra Tipped Gameking over 41.9gr H4350 in Starline SRP brass with BR-4 primers. Really happy with the results.

So here's my question -- I've fired over 200 rounds of this handload, using large rifle primers, in three different rifles and it shoots ten shot groups into about 1.2-1.3 MOA, reliably. This was my first attempt with small rifle primers with this bullet, and I plan to shoot another group this weekend. Anyone else seen 6.5 CM groups tighten up just by switching to small primer brass? Or is this just an anomaly?

 

[HighUintas]

Here's a group with a question.

Fired ten rounds from my T3x in 6.5CM into a little less than 0.7" inches yesterday.
I'm shooting a 140gr Sierra Tipped Gameking over 41.9gr H4350 in Starline SRP brass with BR-4 primers. Really happy with the results.

So here's my question -- I've fired over 200 rounds of this handload, using large rifle primers, in three different rifles and it shoots ten shot groups into about 1.2-1.3 MOA, reliably. This was my first attempt with small rifle primers with this bullet, and I plan to shoot another group this weekend. Anyone else seen 6.5 CM groups tighten up just by switching to small primer brass? Or is this just an anomaly?

Mine has that accuracy with 140 match burners and star line srp brass. I use cci450. I haven't tried it with lrp

 

[northernlandgar]

Mine has that accuracy with 140 match burners and star line srp brass. I use cci450. I haven't tried it with lrp

Good to know, thanks.

 

[Mike Islander]

Rokslide special T3X stainless. 18" threaded with Hyperion.

- Black Hills BH-D556N19: 5.56 TMK
- 100 yards
- SWFA 3-9x42 SS HD

 

[The Harbor Master]

Finally got to try some 77gr OTM, almost cut groups in half from the cheap PMC 55gr. I'll blame the evening low light for it not getting under 1moa, but I know I need to keep up the weekly practice.

Tikka T3 Varmint .223

 

[littlebigtine]

Shots 21-32 down the tube with factory norma match. Only gripe is how slow it is at 2550 fps avg out of a 18”. Havent tried any other ammo so we will see if its the ammo or the barrel

 

[Dioni A]

Here’s a 100 yard 30 round group out of my t3x stainless super lite 223. 73eldm loaded with varget using picked up brass from a shoot to hunt class.

 

[philcox]

I must be odd man out … I don’t get groups anywhere near what other folks are getting. here are my “10 round groups”.
- 7PRC - 168 LRX, ADG, CCI250, 67.5g RL26 … C6 20” Barrel

- 6.5CM - Tikka barrel cut to ~20”. 2 loads: 127LRX and 135 DRT … both Peterson brass CCI200, 46.5g StaBALL 6.5

- 223 - Tikka barrel cut to 18”. 2 loads: 77TMK w/ 26.5 CFE223 Starline brass and CCI400, other is 79 DRT factory

Sent from my iPhone using Tapatalk

 

[Juan_ID]

First extended round zero I’ve shot, 35 round zero check. To not clog up Justin’s scope zero check thread @HighUintas, load data is below.
Rifle is a factory 223 chopped to 16.5”, omega 30 suppressor maven rs1.2 krg bravo.
Load is virgin starline 223 brass cci450 23.5gr of xbr and a 73 eld at mag length 2.27”.

 

[The Harbor Master]

I must be odd man out … I don’t get groups anywhere near what other folks are getting. here are my “10 round groups”.
- 7PRC - 168 LRX, ADG, CCI250, 67.5g RL26 … C6 20” Barrel

- 6.5CM - Tikka barrel cut to ~20”. 2 loads: 127LRX and 135 DRT … both Peterson brass CCI200, 46.5g StaBALL 6.5

- 223 - Tikka barrel cut to 18”. 2 loads: 77TMK w/ 26.5 CFE223 Starline brass and CCI400, other is 79 DRT factory

Curious, as I don't use that Hornady app... are the green and blue circle x's used to indicate an inch for reference? If so, aren't those orange circles 1" at the outer edge?

Just wondering if maybe you're selling yourself short on the measurements.

 

[Harvey_NW]

Curious, as I don't use that Hornady app... are the green and blue circle x's used to indicate an inch for reference? If so, aren't those orange circles 1" at the outer edge?

Just wondering if maybe you're selling yourself short on the measurements.

Judging by perspective, I think those are 2" targets. Here's a 6.5mm group on 1" target for reference.