RokStok

[david2duck]

I had the same issue with my recoil lug. Tried setting it with the action but it wouldn’t budge. Tried to pull it with vice grips and my buddy holding the stock, wouldn’t budge. We tried for over an hour with different pliers, vice grips, etc. I finally took a hammer and seated it as deep as it would go. Hopefully it shoots lights out and I’ll forget about it.

I’m not upset or complaining about stockys or UM. I made the decision to do what I did. I have hunts coming asap and didn’t want to ship it back and wait any longer.

 

[sveltri]

I measured my factory and the MT lug last night. The factory lug I had measured .005 shorter than the MT. Going to shoot with the factory and see if there's any difference for me.

 

[Moosehunter]

Pics of the wood rokstok on the gram sure make a guy want one!

Could you post a pic here?
I'm not on the gram I ges..

 

[pods8 (Rugged Stitching)]

Could you post a pic here?
I'm not on the gram I ges..

Not sure if there were others, I see this one readily.

 

[IrkedCitizen]

Could you post a pic here?
I'm not on the gram I ges..

Full picture on page 293

RokStok

I'll just say it, LE Green is too hard to do, yet we are gonna put up pics of the wood version that will be even harder to complete? Gold RS was canceled, green is trying to be replaced. I know this has been difficult, and I feel like I have been really patient, being a 10% and all. Just...

rokslide.com

 

[JCMCUBIC]

I had the same issue with my recoil lug. Tried setting it with the action but it wouldn’t budge. Tried to pull it with vice grips and my buddy holding the stock, wouldn’t budge. We tried for over an hour with different pliers, vice grips, etc. I finally took a hammer and seated it as deep as it would go. Hopefully it shoots lights out and I’ll forget about it.

I’m not upset or complaining about stockys or UM. I made the decision to do what I did. I have hunts coming asap and didn’t want to ship it back and wait any longer.

I just spent 1/2 an hour trying to pull it. Only succeeded in marring the lug. I finally got pissed off, put a hard rubber handle on top of the lug, and used a metal bar in an attempt to tap it in...which turned into hammering hard...which as far as I can tell hasn't moved it. Tomorrow I'll give it another shot with a hammer.

For those who made the recommendation of seating it and letting the action screws pull it down, it's way to high for screws to make any engagement. Even if they were long enough...and I may have some stock maker screws that are...I'm doubtful the plastic bm would hold up very well.

 

[david2duck]

I have two more stocks showing up today so we’ll see

 

[T_Widdy]

I just spent 1/2 an hour trying to pull it. Only succeeded in marring the lug. I finally got pissed off, put a hard rubber handle on top of the lug, and used a metal bar in an attempt to tap it in...which turned into hammering hard...which as far as I can tell hasn't moved it. Tomorrow I'll give it another shot with a hammer.

For those who made the recommendation of seating it and letting the action screws pull it down, it's way to high for screws to make any engagement. Even if they were long enough...and I may have some stock maker screws that are...I'm doubtful the plastic bm would hold up very well.

What did um say to do?

 

[Moosehunter]

Full picture on page 293

RokStok

I'll just say it, LE Green is too hard to do, yet we are gonna put up pics of the wood version that will be even harder to complete? Gold RS was canceled, green is trying to be replaced. I know this has been difficult, and I feel like I have been really patient, being a 10% and all. Just...

rokslide.com

My bad
Thankyou!

 

[HighUintas]

I'm not sure how guys seemed to make a bigger ruckus about imperfections in the bare carbon finish than the lugs not seating properly. That's a huge quality and functional issue which should have been easily caught. I'd be embarrassed sending out stocks with that problem.

 

[Cameron.25]

Mine shipped out today, hopefully the lug isnt an issue for me lol

 

[HingleMcCringleberry]

I'm not sure how guys seemed to make a bigger ruckus about imperfections in the bare carbon finish than the lugs not seating properly. That's a huge quality and functional issue which should have been easily caught. I'd be embarrassed sending out stocks with that problem.

I can only speak to mine, but it appeared to be a couple thousandths...maybe a few. I can see how that would go unnoticed. Heck I didn't notice it until I compared it to another stockys stock.

 

[Antares]

Just got shipping notification.

Bare carbon, spacers, pic rail, Ace #3 channel.

Ordered 12/26.

 

[Tartan]

Just got my shipping notice as well.

12/21 order
Tikka, no rail, sendero, spacers, custom cerakote

 

[HingleMcCringleberry]

I couldn't leave well enough alone..

Some spray paint, sponges, and 5mins. I wanted the orange to be brighter, but it will wear off and I will repaint it. #spraypaintlife

 

[mxgsfmdpx]

Not sure if there were others, I see this one readily.

For those without Instagrams... Would somebody be please a lamb and let me know in here when a wood version goes up for ordering please? I need 2 and my father in law wants 2.

 

[HingleMcCringleberry]

For those without Instagrams... Would somebody be please a lamb and let me know in here when a wood version goes up for ordering please? I need 2 and my father in law wants 2.

I would be willing to bet they are a MRC exclusive. But that is pure speculation

 

[mxgsfmdpx]

I couldn't leave well enough alone..View attachment 744744

Some spray paint, sponges, and 5mins. I wanted the orange to be brighter, but it will wear off and I will repaint it. #spraypaintlife

Looks good! Next time you gotta go get some of this color! My local Ace hardware has it. It's even brighter than the construction marking paint neon orange. Photo here makes it look really red, it's not that red.

 

[mxgsfmdpx]

I would be willing to bet they are a MRC exclusive. But that is pure speculation

Yucky if true.

 

[roosiebull]

I couldn't leave well enough alone..View attachment 744744

Some spray paint, sponges, and 5mins. I wanted the orange to be brighter, but it will wear off and I will repaint it. #spraypaintlife

Looks great! I plan on going with orange/gray tear on my next