RokStok

[finner]

Got my stock in yesterday. Anyone have any issues with the inletting and bottom metal? I have tried 3 different barreled actions and 3 different bottom metals and 4 different mags. They all fit, but the factory mags are really hard to get in like abnormally hard. Tried another friends rokstock and all actions/dbm/mags worked in his and were significantly better. Tried to see if anything was contacting in my stock but couldn’t find anything. Let me know what ya guys think

You may have to shim the bottom metal out from the stock to get reliable feeding and mag retention. I had to with my Rokstok and an Alterra on another Tikka. You can use washers, but these are better:

Tikka T3/T3x Shim Kit

Do you have a hard time seating the magazines on your stock Tikka T3 Rifle? Due to a slight variance in the trigger guard and the stock, sometimes a Tikka T3 would benefit from a shim or two. Kit includes 8 custom shims. 4 that are .010 inches and 4 that are .020 inches. Includes T25 TORX bit...

highdesertrifleworks.com

 

[Bc45]

You may have to shim the bottom metal out from the stock to get reliable feeding and mag retention. I had to with my Rokstok and an Alterra on another Tikka. You can use washers, but these are better:

Tikka T3/T3x Shim Kit

Do you have a hard time seating the magazines on your stock Tikka T3 Rifle? Due to a slight variance in the trigger guard and the stock, sometimes a Tikka T3 would benefit from a shim or two. Kit includes 8 custom shims. 4 that are .010 inches and 4 that are .020 inches. Includes T25 TORX bit...

highdesertrifleworks.com

I have been using all factory plastic bottom metals, the shims are still good for it even if it’s not their metal one?

 

[RyanT26]

@Unknown Munitions
Does BDL inlet on the Rem 700 add additional cost?

 

[Bluumoon]

Got my stock in yesterday. Anyone have any issues with the inletting and bottom metal? I have tried 3 different barreled actions and 3 different bottom metals and 4 different mags. They all fit, but the factory mags are really hard to get in like abnormally hard. Tried another friends rokstock and all actions/dbm/mags worked in his and were significantly better. Tried to see if anything was contacting in my stock but couldn’t find anything. Let me know what ya guys think

Give Unknown a call if there is a concern.

 

[Ryan Avery]

Got my stock in yesterday. Anyone have any issues with the inletting and bottom metal? I have tried 3 different barreled actions and 3 different bottom metals and 4 different mags. They all fit, but the factory mags are really hard to get in like abnormally hard. Tried another friends rokstock and all actions/dbm/mags worked in his and were significantly better. Tried to see if anything was contacting in my stock but couldn’t find anything. Let me know what ya guys think

I’ve had this issue with almost every stock manufacturer except Manners. Gonna have to shim it. The bottom inlet is a touch too deep.

 

[Bc45]

I’ve had this issue with almost every stock manufacturer except Manners. Gonna have to shim it. The bottom inlet is a touch too deep.

Perfect thanks. Everything else is solid excited to get some rounds through it!

 

[mxgsfmdpx]

Got my stock in yesterday. Anyone have any issues with the inletting and bottom metal? I have tried 3 different barreled actions and 3 different bottom metals and 4 different mags. They all fit, but the factory mags are really hard to get in like abnormally hard. Tried another friends rokstock and all actions/dbm/mags worked in his and were significantly better. Tried to see if anything was contacting in my stock but couldn’t find anything. Let me know what ya guys think

My Stockys VGs and my Rokstok have all been VERY tight, not allowing certain mags to easily click in. I assumed this was due to using aftermarket bottom metals and a very tight tolerance on the inletting. A little sand paper and knocking coatings off metal mags and they work fine. Haven't had any issues with factory plastic mags.

 

[mxgsfmdpx]

Also, with the high desert aluminum factory clone bottom metals that I use, I added in their thinnest shim to each action screw which seemed to help (their bottom metals come with 3 different thickness shims).

 

[wind gypsy]

Seems pretty common for the inlets to be a little deep. I used all of the shims high desert sends with their bottom metal and its still a hint tight getting a mag to latch.

 

[Ryan Avery]

……..


Sent from my iPhone using Tapatalk Pro

 

[kswaterfowl]

……..


Sent from my iPhone using Tapatalk Pro

What??? That is sweet!

 

[clperry]

……..


Sent from my iPhone using Tapatalk Pro

Oh no…..


Sent from my iPhone using Tapatalk

 

[Antares]

Love the stippling! I much prefer that to checkering.

 

[eric1115]

……..


Sent from my iPhone using Tapatalk Pro

Dude, where do we sign up for pre-order? How long till they are available?

 

[Brucebarker024]

……..


Sent from my iPhone using Tapatalk Pro

Yup, gonna need one of those.

 

[mdtennant]

……..


Sent from my iPhone using Tapatalk Pro

Hmmm. So this is why you don't have one for the x-bolt. Diverting resources.

 

[IrkedCitizen]

Hmmm. So this is why you don't have one for the x-bolt. Diverting resources.

@Stockys doesn't make anything for the xbolt

 

[HighUintas]

Wtf. I know stockys has a duplicator. Get those things rolling out. I need one.

 

[HighUintas]

At least give us a full view of it!

 

[mdtennant]

@Stockys doesn't make anything for the xbolt

Not yet. I asked earlier this week. They said it was on their radar, but have not had time [i.e resource dedication]. I was going to poke Rayan and Jake for taking up all Stocky's resources for the RokStok, but I have one of those on order too.

I am just hoping for a decent stock for the x-bolt and what is available ranges from mediocre to garbage.