Refillable 1# propane bottles/kit?

*zap*

WKR
Joined
Dec 20, 2018
Messages
7,760
Location
N/E Kansas
Anyone use these? How was it? what brand?
I want to switch from refilling the coleman bottles that I originally purchased full of 1#.
 
Joined
Jul 7, 2021
Messages
44
I have a couple. They work just fine. I had to buy a tool to fill them, but it wasn't terribly expensive and it's been worth it for me. I'm happy to go away from disposable propane bottles. The brand I bought is Flame King.
 
Joined
Sep 23, 2022
Messages
405
Location
Carolinas
I’ve got a few 1#’ers from Manchester tank and flame king, though I’m not sure Manchester makes them (1#) anymore. The refill coupling is about $10-$12 and works to fill from larger tanks, pretty handy to have. 3 of the 4 flame kings I’ve bought have made it more than 4 years, had a seal on one last year that went bad after the housing caught some rust following an extended outing on the coast. I’d buy them again when I need to lifecycle the current inventory.
 
OP
*zap*

*zap*

WKR
Joined
Dec 20, 2018
Messages
7,760
Location
N/E Kansas
That is good also.^

The flame king bottles you need a allen key to bump. The Mr. Heater bottles have a valve with a ring attached so you just pull the ring.....>I think<
 

TWoch

FNG
Joined
Mar 27, 2024
Messages
25
I bought an adapter from the farm store to refill all my #1 bottles off a grill tank. Pays for itself in about 3 bottles. Make sure you empty all the bottles beforehand so they’ll fill fuller.
 

Wrench

WKR
Joined
Aug 23, 2018
Messages
6,303
Location
WA
I bought an adapter from the farm store to refill all my #1 bottles off a grill tank. Pays for itself in about 3 bottles. Make sure you empty all the bottles beforehand so they’ll fill fuller.
Take more out so more fits? I don't follow. A 1# bottle holds 1#. If I take out 8oz on the bbq....it still takes 8oz to top it off in my head.

Please explain if that's not the case.
 

Jbxl20

WKR
Joined
Dec 29, 2020
Messages
875
Location
PA
Take more out so more fits? I don't follow. A 1# bottle holds 1#. If I take out 8oz on the bbq....it still takes 8oz to top it off in my head.

Please explain if that's not the case.
I think he means you need to purge the air to fit more liquid.
 

Iowafarmer

Lil-Rokslider
Joined
Jan 5, 2023
Messages
150
I’ve got a liquid valve on my 1000 gallon propane tank that I fill my 20# tanks with then I use an adapter hose to run my buddy heater in my deer blinds 1 tank last all season where the 1# tank lasts about two and a half hours
 

TWoch

FNG
Joined
Mar 27, 2024
Messages
25
Even after the little tank is empty of fuel there will still be pressure in the tank. If you screw the adaptor on the large tank first then attach the little bottle, with that pressure still inside, it doesn’t allow as much gas to flow into little bottle before it’s “full”. If you screw it to the little bottle first it’ll empty. I don’t know if it helps, but I always invert my large tank so liquid fuel is at the nozzle. I run buddy heaters and cook stoves that burn through a lot of fuel.
 

taskswap

WKR
Joined
Oct 6, 2021
Messages
537
You can also just bump the little pressure relief valve, with a key/allen key/etc like someone posted above. Another trick is putting the 1# bottles in the freezer for a few hours ahead of time.

One caution, when you refill bottles this way they run fine for 95% of the small-bottle appliances out there. But Mr Buddy heaters are notoriously sensitive to oil contamination, and when you use 20lb cylinders with an extension hose you're supposed to use an oil filter. I've personally ruined one not doing this - there's a way to clean it, but it was a lot of hassle and I crimped a tube accidentally trying to do it. Best avoid it if you can. This filter is a pretty cheap add-on accessory that screws right onto the 1lb-bottle-port on the heater and then you connect the hose to that. Well, if you REFILL 1# cylnders from a 20# source, you're running the same oil-contamination risk. So if you're planning to run a Mr Buddy off refilled cylinders, you might want to have the same filter installed. It makes it more bulky, though.
 

dtrkyman

WKR
Joined
Oct 2, 2014
Messages
3,191
I use old bottles I had already, keep an eye out for leakers, that little valve goes bad and I had to toss a couple!

Freezer trick works well and I even put the large tank in the sun so it's a lot warmer.
 
OP
*zap*

*zap*

WKR
Joined
Dec 20, 2018
Messages
7,760
Location
N/E Kansas
I use old bottles I had already, keep an eye out for leakers, that little valve goes bad and I had to toss a couple!

Freezer trick works well and I even put the large tank in the sun so it's a lot warmer.
I had some leak also and then gave the overpressure valve a shot of blaster and a shot of blaster in the one # bottle ....never had a leaker doing it that way. A curved forceps will allow you to pull the overpressure valve out to bump it....

But, I am going to go with the mr. heater one pound kegs now. and a five pound bottle for car camp.
 

mt terry d

WKR
Shoot2HuntU
Joined
Jul 18, 2023
Messages
739
My method:
20# tank upside down
Weigh empty bottle.
hook up.
purge air from 1# can with the relief valve
open 20#
when you quit hearing gas flow shut off.
purge some air.
fill again
weigh
looking for @ 16 oz + empty wt
purge & fill again if necessary
 
Joined
Sep 26, 2023
Messages
10
Flame king works good only problem I have had is the relief valve that uses the hex key stripped out. Totally my fault other than that they have been great. Use them all year long.
 

sasquatch

WKR
Joined
Jul 26, 2015
Messages
925
Been using flame kings for years now, never had an issue.

Didn’t know of the newer Mr buddy ones, but just ordered one. I like the idea of not needing the Allen wrench if it works good.


Sent from my iPhone using Tapatalk Pro
 
OP
*zap*

*zap*

WKR
Joined
Dec 20, 2018
Messages
7,760
Location
N/E Kansas
mr heater bottles have a ring that allows the relief valve to be opened.....no threads. Tractor Supply should have them in stock.
 
Top