My knife builds

GARLICSALT

Lil-Rokslider
Joined
Jul 19, 2021
Messages
171
No new knives in this post, but pretty happy to have achieved a goal around 10 days ago. For the last 18 months I have been working towards becoming a member of the Australian Knifemakers Guild. The Guild has two categories of knife makers, a Probationary Member and a Full Member. There is a third category Life Member if selected & voted for by the membership, but there are only a handful of these. At a high level, you can think of it in terms of a Probationary Member being an entry level knife maker, and a full member is an advanced knife maker. Thats not a perfect description, but its near enough.

To advance to these levels, there is a formal checklist of requirements (see here if interested https://akg.org.au/wp-content/uploads/2022/06/FULL-DOC-Assessment-Checklist-for-Guild-Membership.pdf). To get to Probationary membership, you need to present 3 knives for assessment and achieve a mark of 10 out of 20 for each knife. Once you are a Probationary Member, you can sit for Full Member a minimum of 12 months later and need to achieve a minimum of 18 out of 20 for each of the 3 knives, but there are also specific things you need on the assessment knives that are not required for the probationary test.

I have been working for a while to get 3 knives to have assessed, but I keep on picking some fault and deciding its not at the standard required. Occasionally I have a really fantastic knife finished that I am super happy with, but its promised to someone with a very close deadline, so I cant hang onto it until I have the other knives I need to make up the set of three for assessment.

Anyhow, I finally booked a date to go see Adam Parker, one of 2 Guild assessors in Victoris, and a guy with over 30 years of knife making experience. Adam is between Geelong and Ballarat, and with the traffic on Wednesday, it took me 3 hours each way to go see him.

I had a couple of knives that I recently finished, plus I was planning to use a kitchen knife I just finished a day before the appointment. But I found a few scratches on the blade that I wasn't happy with, so at the last minute I took a survival knife I finished a few months ago to make up the required knives.

At the end of the assessment process, I ended up scoring 16 out of 20 for the survival knife, 18 out of 20 for the bushcrafter, and 20 out of 20 for the hunter. So as of Wednesday, I am a Probationary Member of the Australian Knifemakers Guild!

IMG-6235.jpg


IMG-6239.jpg
16/18/20 out of 20 you crushed it, congratulations!!! From the looks of the work, well deserved. Keep em coming. As you can see the guys love looking at great custom knives.
 
OP
R
Joined
Dec 23, 2020
Messages
381
After the last boner I made, I was asked to make a very similar knife for someone else. It worked out well as I had one profiled and heat treated ready to grind. They also wanted a kydex sheath that wasnt grey or black, so I went high viz which I think is pretty practical for a knife that will get used like this one will.

The blade is NitroV steel, with the same very shallow hollow grind as the last one. The edge is ground down to .25 of a mm, so should slice well. The handles are black Richlite with orange G10 liners and pins. The sheath is orange Kydex.

IMG-6302.jpg


IMG-6297.jpg


IMG-6295.jpg


IMG-6294.jpg


IMG-6287.jpg


IMG-6288.jpg
 

jolson

FNG
Joined
Nov 23, 2012
Messages
14
These all look great. I’ve been building for a couple years now as well. Not sure they look as professional as yours.
Just finished these three this weekend
IMG_0761.jpeg
IMG_0762.jpegIMG_0767.jpegIMG_0764.jpegIMG_0770.jpegIMG_0771.jpeg
 

Attachments

  • IMG_0761.jpeg
    IMG_0761.jpeg
    613.8 KB · Views: 6

BBob

WKR
Joined
Jun 29, 2020
Messages
4,548
Location
Southern AZ
The blade is NitroV steel, with the same very shallow hollow grind as the last one. The edge is ground down to .25 of a mm, so should slice well. The handles are black Richlite with orange G10 liners and pins. The sheath is orange Kydex.
I love that shape. Utilitarian but at the same time very svelte and beautiful! All the curves just work together. I'd love to have one like it.
 
OP
R
Joined
Dec 23, 2020
Messages
381
OP
R
Joined
Dec 23, 2020
Messages
381
This is a bit of a design tweak on a knife I have made once before. The blade shape gives it a good drop point and also plenty of belly, so hopefully a good all round field prep knife.

The steel is 2.5mm N690 stainless. I have taken the edge down to 0.2mm, and the point has a good taper on it, so it should slice well, and also poke into game easily. The handle is green G10, with orange G10 liners & pins.

IMG-6398.jpg


IMG-6400.jpg


IMG-6403.jpg


IMG-6407.jpg
 
OP
R
Joined
Dec 23, 2020
Messages
381
Another of my experiments with Woodlore style knives. This one is a true scandi grind, so pretty faithful to the original Woodlore design.

The steel is 3mm NitroV with a tapered tang. The handle is stabilised European Birch, with black G10 liners & loveless bolts and a brass lanyard tube, Pretty happy with how it came up.

IMG-6525.jpg


IMG-6531.jpg


IMG-6533.jpg


IMG-6538.jpg
 

RiceTc

FNG
Joined
Apr 11, 2019
Messages
8
This one is inspired by the Half Face Blades Crow Scout. Full tang, flat grind blade in 3.8mm Elmax. Handle is camo G10, with G10 pins and carbon fiber lanyard tube. I still need to make a kydex sheath and sharpen the edge, but otherwise its done.

IMG-0412.jpg


IMG-0419.jpg


IMG-0424.jpg


IMG-0425.jpg
These are incredible!!
 
OP
R
Joined
Dec 23, 2020
Messages
381
These are a couple more willow leaf knives I finished last week. As with the last one I posted, the steel is 2.5mm N690 stainless. As with the last one, I have taken the edge down to 0.2mm, and the point has a good taper on it, so it should slice well, and also be pretty pointy. Both have handles in G10, with G10 liners & pins. One of the last things I did was make kydex sheaths for these right before I went to the show.

unnamed-15.jpg



unnamed-11.jpg


unnamed-6.jpg


unnamed-4.jpg


unnamed-24.jpg


unnamed-22.jpg


unnamed-21.jpg


unnamed-18.jpg


unnamed-27.jpg
 
OP
R
Joined
Dec 23, 2020
Messages
381
Thought you guys might enjoy some photos of my latest boner. The steel is 2.5mm NitroV, with a slight hollow grind in the bevel which tapers to about 0.2mm to give it a slicey edge. The handles are camo G10 with G10 orange & white liners and G10 pins.

unnamed-11.jpg


unnamed-7.jpg


unnamed-6.jpg


unnamed-2.jpg


unnamed-35.jpg
 
Top