Let's See Your Semi-Custom Tikka Builds

[TheViking]

-Tikka Roughtech in 6.5cm Chopped to 20”and threaded. (4lbs 11oz)
-Mesa precision Altitude stock (32oz)
-Glades bolt hand and knob
-Talley lightweight low rings (2.5oz)
-Trijicon Tenmile 3-18x50 (25.7oz)

Weighs 8lbs 8oz. Could shave off some more weight with a Stockys and a smaller scope.

View attachment 770588

I have basically an identical setup, except in 6.5 PRC and I love it. I wanted a to shave some weight on another build so I built a 6 CM last winter with a Stockys and I don’t like it nearly as much as the Mesa/Pure Precision stock. Gun feels very front heavy and I don’t like that at all.

 

[OneShot]

I have basically an identical setup, except in 6.5 PRC and I love it. I wanted a to shave some weight on another build so I built a 6 CM last winter with a Stockys and I don’t like it nearly as much as the Mesa/Pure Precision stock. Gun feels very front heavy and I don’t like that at all.

After this weekend, I have the same thoughts on the Stockys. I have a VG2 in a 700. Didn’t pay much attention to the the balance because I took a factory stock off and swapped immediately. Ended up selling that gun and had the stock laying around. This weekend my brother put together his new Impact and tried the Stockys on the gun. He didn’t like it and mentioned how front heavy it was. He ended up grabbing an AG Alpine Hunter, the balance was really nice and didn’t feel front heavy at all.

 

[MBAlex]

Rebarreled to a 6CM 22 inch barrel and put it in a Bravo

 

[sportsmans challenge]

Just got this action rebarreled from a 25 saum to a 25x7prc. Twisted barrels did the chamber(@T_Widdy )
22" #4 mcgowan 7.5 twist fluted at Kampfeld Customs.

Waiting on some dies from redding to show up

 

[Mountainrancher]

T3x superlite 6.5cm
Just got it back from the smith after having 4 inches chopped of the barrel and threaded.
Stockys vg stock olive web
Unknown rings
Trijicon tenmile 3-18 mil
Huxwerx ventum 7.62
Everything torqued with paint pen

 

[HighUintas]

T3x superlite 6.5cm
Just got it back from the smith after having 4 inches chopped of the barrel and threaded.
Stockys vg stock olive web
Unknown rings
Trijicon tenmile 3-18 mil
Huxwerx ventum 7.62
Everything torqued with paint pen
View attachment 772029

How do you like that huxwerx? They're interesting for sure... Just expensive

 

[Mountainrancher]

How do you like that huxwerx? They're interesting for sure... Just expensive

The ventum is a steel case with titanium core so it’s a little cheaper, about 1200 all in. It’s my first can and the only can I’ve really been around so I’m not sure how it compares sound wise. It’s as quiet as I need it to be and from the little bit of info I could find it should be hearing safe. The flow through seems to work well I’ve shot it on my ar without an adjustable gas block and it functions fine and no gas to the face.

 

[therealblanket]

Finally feel like I can contribute to this thread:
-Started as a 7mmrm superlite
-Swooped a SS 7rm ($100 tikka takeoffs go crazy) and had it cut down to 20” and threaded 1/2-28
-Mc Game Warden 2.0
-NX8 4-32 in NF rings w/ top ring level
-Q Trash Panda (I am filled with regret)
-Atlas CAL tall (love the usability hate the weight)

Shoots great with factory 162g ELDX. A bit of a bear to tote, hoping to put it on a diet but not sure where to cut weight without sacrificing shootabilty. Considering following the Rokslide trend and moving down to some flavor of 6.5
Open to any critique
View attachment 759374

What weight are you currently sitting at?
I am working on a project that is eerily similar to this and want to stay light, but functional with minimal recoil. I know compared to your setup, my optic is around 9 ounces lighter. But, I am not sure I would change too much else - maybe the can for a brake until I get a Ti can, and then no bipod (using my trekking poles).

Appreciate any insight.

 

[ssramage]

I've followed along with this thread for a while, but never could participate. Still not sure mine falls in the same category as a lot of these on here, but it's a start!

Tikka T3x compact 7mm-08 w/ Factory barrel threaded at standard 20" length (bought from member on here)

Added:
Stocky's VG Carbon Hunter
Rugged Flash Hider for mounting Razor 7.62
Unknown Munitions Rings
Zeiss Conquest V4 3-12x56

 

[solarshooter]

Sharing my latest build:

• Stainless action, standard bolt face, short action bolt stop and mags
• Bartlein #3 6mm 1:7.5" twist, chambered in 6CM with a SAAMI spec reamer by Unknown Munitions, cut at 18" and threaded 5/8"x24. Ordered blank from bugholes, UM cut as a prefit and installed myself.
• Factory trigger with light weight trigger spring from Mountain Tactical
• Factory stock, widened barrel channel, Tikka wide forend, Tikka vertical grip, Mountain Tactical cheek riser, Limbsaver recoil pad
• UM Tikka rings and level
• Trijicon Tenmile 3-18x44 FFP in mils
• SiCo Scythe Ti

All up weight is 9.75lbs as shown. Barrel came in thicker than I hoped but it shoots like a dream and I don't mind the weight. Groups with suppressor from yesterday:

Both 10 shot groups, dots are 1". Lower group was after installing suppressor with bare-muzzle zero, measures 0.85". Clicked up 0.3mil and left 0.1mil. Second group was confirmation. Full group measures 0.7", 9 shots in 0.4".

Load details:

• ADG 6CM brass
• CCI 200
• Berger 108 Elite Hunter
• 40.0gr H4350
• MV is 2800fps
• COAL 2.800", jumping 0.040", bearing surface/boattail junction sits just above neck/shoulder junction

 

[therealblanket]

Sharing my latest build:
View attachment 774067

• Stainless action, standard bolt face, short action bolt stop and mags
• Bartlein #3 6mm 1:7.5" twist, chambered in 6CM with a SAAMI spec reamer by Unknown Munitions, cut at 18" and threaded 5/8"x24. Ordered blank from bugholes, UM cut as a prefit and installed myself.
• Factory trigger with light weight trigger spring from Mountain Tactical
• Factory stock, widened barrel channel, Tikka wide forend, Tikka vertical grip, Mountain Tactical cheek riser, Limbsaver recoil pad
• UM Tikka rings and level
• Trijicon Tenmile 3-18x44 FFP in mils
• SiCo Scythe Ti

All up weight is 9.75lbs as shown. Barrel came in thicker than I hoped but it shoots like a dream and I don't mind the weight. Groups with suppressor from yesterday:
View attachment 774073
Both 10 shot groups, dots are 1". Lower group was after installing suppressor with bare-muzzle zero, measures 0.85". Clicked up 0.3mil and left 0.1mil. Second group was confirmation. Full group measures 0.7", 9 shots in 0.4".

Load details:

• ADG 6CM brass
• CCI 200
• Berger 108 Elite Hunter
• 40.0gr H4350
• MV is 2800fps
• COAL 2.800", jumping 0.040", bearing surface/boattail junction sits just above neck/shoulder junction

Great build man! How do you like the Scythe? I keep eyeing it at Scheels.

 

[solarshooter]

Great build man! How do you like the Scythe? I keep eyeing it at Scheels.

It's great, I just added a post here summarizing my experience.

Silencerco Scythe TI review

For the range it is needed I think, but I don't use mine hunting. I keep one on my Scythe when sheep hunting, just to keep from damaging it in rocky terrain. My barrel always seems to get bumped on rocks.

rokslide.com

 

[Antares]

Sharing my latest build:
View attachment 774067

• Stainless action, standard bolt face, short action bolt stop and mags
• Bartlein #3 6mm 1:7.5" twist, chambered in 6CM with a SAAMI spec reamer by Unknown Munitions, cut at 18" and threaded 5/8"x24. Ordered blank from bugholes, UM cut as a prefit and installed myself.
• Factory trigger with light weight trigger spring from Mountain Tactical
• Factory stock, widened barrel channel, Tikka wide forend, Tikka vertical grip, Mountain Tactical cheek riser, Limbsaver recoil pad
• UM Tikka rings and level
• Trijicon Tenmile 3-18x44 FFP in mils
• SiCo Scythe Ti

All up weight is 9.75lbs as shown. Barrel came in thicker than I hoped but it shoots like a dream and I don't mind the weight. Groups with suppressor from yesterday:
View attachment 774073
Both 10 shot groups, dots are 1". Lower group was after installing suppressor with bare-muzzle zero, measures 0.85". Clicked up 0.3mil and left 0.1mil. Second group was confirmation. Full group measures 0.7", 9 shots in 0.4".

Load details:

• ADG 6CM brass
• CCI 200
• Berger 108 Elite Hunter
• 40.0gr H4350
• MV is 2800fps
• COAL 2.800", jumping 0.040", bearing surface/boattail junction sits just above neck/shoulder junction

Looks awesome! I'm having a similar setup put together (18" 6CM). Is that a T3 action?

 

[lineslayer]

Tikka T3x LA
18" Preffered 7 SAUM 1 in 8
Stocky's VG in western viper
Spartan precision gunsmith adapters x2
Extra low leupold rings
4.5-14x40 leupold vx3
Weighs 6lb naked
Currently wearing a nomad-30 but I'm a little Ti-curious. Pushing 168gr ABLR 2775fps with H1000, ADG brass, Winchester LRMs