Hornady FPB

[Baddog]

I bought some 350 grain to try and they are so tight I can't hardly get them started and when I do I end up creasing the nose of them. I'm not super savvy on this muzzleloading stuff. Am I missing something or a trick to get these suckers started?

Its a Knight Mountaineer rifle.

Thanks

 

[corbhenrie]

What gun? Sounds like bore is too small for them by a couple thousandths

Sent from my SM-G975U using Tapatalk

 

[sabotloader]

I bought some 350 grain to try and they are so tight I can't hardly get them started and when I do I end up creasing the nose of them. I'm not super savvy on this muzzleloading stuff. Am I missing something or a trick to get these suckers started?

Its a Knight Mountaineer rifle.

Thanks

Contact 'Ole Hunter' - he uses them and has a method to get them down his Knight ULite.

 

[Ucsdryder]

They’re tight. But they fit. If the gun is dirty it gets real tough. Make sure you start it straight and not crooked. It’ll go. Put on your big boy britches.

 

[txhunter581]

There is a trick to it.

First of all you hav to understand that the body of the bullet is 0.499 but the rear bell is 0.507. So you have to size it to your bore

You need a short bullet started like this:

Thompson/Center T-Handle Short Starter with Universal Loading Tips | Cabela's

This palm-saving starter with removable seating end converts your ramrod into a work rod. Extends ramrod length for easier cleaning and firmer bullet seating. Durable composite construction.

www.cabelas.com

That even has the right loading tip you need

now set the bullet straight in the end of the muzzle and put the short starter on top. Hold the muzzle/ bullet/ end of the starter with one hand and give the T handle a sharp “WHAP” with your other hand. May take a couple of whaps. That should start the bullet and size it. Then take your ramrod and seat it the rest of the way. It does still take a little pressure ( I think they say about 25 lbs). So I like to use a ramrod with a folding T handle like this.

Thompson/Center Power Rod Ramrods | Cabela's

Make loading your rifle faster, without pain, and with more uniform seating pressure for consistency. Pivoting T-handle is integrated into the solid aluminum rod. Tip accepts 10-32 threaded

www.cabelas.com

That is not the exact one you need because it is for T/C rifles. They make a universal one you can cut to the right length.

or you could use one of these with your own ramrod:

Thompson/Center Flex Priming Palm Saver | Cabela's

Buy the Thompson/Center Flex Priming Palm Saver and more quality Fishing, Hunting and Outdoor gear at Bass Pro Shops.

www.cabelas.com

 

[cowboy300]

Lee Bullet Lube Sizing Die Kit 501 Diameter

The Lee Lube and Size Kit is one of the fastest and easiest ways to lubricate and size cast bullets. The sizing die that comes with the kit fits in any...

www.midwayusa.com

The best thing I ever did for shooting Hornady FPBs is pre sizing them with the lee kit. Works great for my CVA rifles

 

[txhunter581]

Did that work For more than one gun? All mine are different sizes including a white that is 0.504

 

[ole hunter]

My Knight Ultra Lite .50 cal has a 501 bore .I resize using a Lee resizing die . The slide right in . They hammer elk hard .

 

[Baddog]

Slightly more complicated than I was hoping for but I’ll make it work

 

[txhunter581]

The short starter is really all you need for sure. Cheap fix

There is really nothing much about muzzleloading that is easy. Can be frustrating, but also one of the reasons I enjoy it.

 

[Baddog]

Shot them today. Using a rubber mallet to get them started straight then they go right in (don’t laugh)... Used 100 grains of triple 7 does that seem like a reasonable amount? Shooting about 2” groups at 65 yards.
Thinking I’m going to do the lee sizer or try different bullets.
Thanks for the insight. Pretty confident in shooting and screwing around with centerfire guns but muzzleloaders are all new to me...

 

[txhunter581]

Here is the next one I would try.

Buy Lead Tipped Muzzleloader Bullet .50 Ammo 350 | PMZ50LMZ1

Shopping for the Lead Tipped Muzzleloader Bullet - Learn more about the latest Muzzleloading and other hunting or shooting gear at Federal Ammunition.

www.federalpremium.com

Also if you stay with the Hornadys. Clean your guns and while the breechplug is still out push a few bullets down thru the barrel and out the breech. Those are the bullets you take with you hunting. They are presized and easy to load in the field. Be sure to push them thru on a padded surface so they don’t get dinged on a Hard surface.

 

[Baddog]

I’m going to do a half dozen that way and try it in a couple days. That seems like a idea and would make life easy

 

[txhunter581]

And I guess you know they don’t make Hornady FPBs any more. There is only one source for them and when they are gone, they are gone.

 

[pnw]

,

I kind of wonder if they actually really are I just bought a hundred blemished 350s from midway USA a few weeks ago and I dont recall seeing them on there before hopefully they made a batch for somebody

 

[txhunter581]

I have not heard that they are making them again. Last I heard this company bought all remaining bullets from Hornady and they only have the 350s left. I ordered 150 from them. Unblemished:

Hornady® FPB™ Muzzleloader Bullets - .50 Caliber Full Bore Bullets 300 & 350 Grain

Shop Now! Hornady FPB® Full Bore Muzzleloader Bullets - 300 & 350 Grain .50 Caliber - Full Bore Flex Tip™ Bullets Today! 15 Pack. Free Shipping with Gun Purchase. Best Prices, Fast Shipping, Expert Advice!

www.muzzle-loaders.com

 

[ole hunter]

Quit makin them ,, Dang will not be test shooting them anymore , Have some thors I will use for rats and targets .