Best adhesive for bonding pic rail to receiver?

[AZ_Hunter]

how do you get these products off?

 

[ResearchinStuff]

Mostly the idea is that you don't want it to come off, ever.

 

[WeiserBucks]

how do you get these products off?

You bond it so that it doesn't come off, that's the whole point of doing it in the 1st place.

 

[AZ_Hunter]

You bond it so that it doesn't come off, that's the whole point of doing it in the 1st place.

I get that but that’s where I get hung up a bit.

I got some work done on an older Tikka Boar Hunter rifle which has the factory rail. I knew the rail was glued on from the factory and told my smith to cerakote the receiver and rail as one, don’t try to separate it. He didn’t listen and I got a phone call talking about a sheered bolt head…

I was pissed and explained that’s why I said to leave it on as one… he got it off eventually, and while the smith was dumbass and didn’t listen, I like to work on/change my guns around a lot. My ideal would be something solid yet can be easily removed via heat more easily.

So I was going to put the rail back on and bed it with blue locktite.

Any issues with that versus the more robust 380 type adhesives?

 

[ResearchinStuff]

Jb weld breaks free with moderate heat and a sharp impact. Getting it scraped off the two pieces though is a pain.

 

[4th_point]

So I was going to put the rail back on and bed it with blue locktite.

Any issues with that versus the more robust 380 type adhesives?

If 242/243 has worked for you in the past, I don't think I would change. It can be a pain in the neck to remove from a receiver though.

242 and 243 work great for bedding, as you probably know. It doesn't provide adhesion, but you already have incredible clamping force from the fasteners, and it does really well at filling gaps to help prevent relative motion.

I am always amazed by how much of a gap can be present between a mount/rail and a receiver. Many super glues, even rubber enhanced, are not meant for gap filling.

Compliance should be a concern as well, in terms of relative motion, especially with a large gap filled with rubberized anything. Check the manufacturer recommendation and make sure it is suitable. Something meant to adhere a fiber optic or tritium light tube may not be suitable for a mount/rail.

Standard super glue can prevent relative motion of two parts with tiny gaps, but is not suitable for this application. I use it for sensitive test equipment, where it has a decent range of application but the actual product used depends on the different factors!

 

[ScreamingPotato]

Super glue gel do any good between rail and receiver, or more harm than good? Asking for a friend literally, he's at the range troubleshooting and gonna remove and remount everything and his wife has super glue gel in her purse lol.

 

[ResearchinStuff]

I don't think it will be strong enough to matter

 

[Choupique]

Super glue gel do any good between rail and receiver, or more harm than good? Asking for a friend literally, he's at the range troubleshooting and gonna remove and remount everything and his wife has super glue gel in her purse lol.

I don't see how super glue could hurt as long as it's cured.

 

[5811]

how do you get these products off?

Set an iron on top of the rail to heat it.

 

[Choupique]

I guess this is as good as place as any to ask since it's already been bumped -

Why so much love for 380 vs the 6xx series retaining compounds?

 

[NSI]

Any recommendations on the best adhesives for permanently bonding a picatinny rail to a rifle action? I've seen that Loctite 380 works great but I cant find any locally. I'd guess JB Weld would work fine. Anything else?

Easy to find on Amazon. Or save money by using any rubberized cyanoacrylic (like arrow fletching glue).

-J

 

[BBob]

Or save money by using any rubberized cyanoacrylic

IC-2000 | Rubber-toughened CA

Rubber-toughened Cyanoacrylate sepcially formulated for shock resistant bonds.

bsi-inc.com

https://www.hobbytown.com/bob-smith-industries-ic2000-black-rubber-toughened-1oz-bsi118/p37065

 

[stevie]

Brownells also carries the little tube. So far bonded one rail and 2 Unknown bolt knobs/handles with plenty left in the tube.

 

[Castle Rock]

I would rather us an epoxy due to the longer working time and easy clean up