Anyone running a 300 WSM with a 22" barrel suppressed?

[STAxel]

Hey looking to work on a new build...is anyone running a 300 WSM with a 22" barrel and using a suppressor? What velocities are you getting with 180gr bullets (factory loads)? Is a 300 WSM at 22” still smoking a 30’06 at 24”?

How's the handling with the overall length? Bonus points if you have any feedback with the Thunderbeast Ultra 7 (gen2) with a .30 cal magnum with that 22" barrel length...And if you got pictures to show off I'd appreciate it.

 

[Brightwhite]

I have the exact setup you are talking about. I will PM you.

 

[bhylton]

I have the exact setup you are talking about. I will PM you.

If you are willing to share anything openly, i would be interested as well. thinking about taking my 22in 300wsm down to 20 inches for a suppressor

 

[STAxel]

If you are willing to share anything openly, i would be interested as well. thinking about taking my 22in 300wsm down to 20 inches for a suppressor

How’s the performance on your current 22”? What sort of velocities are you getting?

 

[bhylton]

shooting 166gr hammer hunters now around 3050. probably leaving 50-70fps on the table due to short magazine/powder capacity issue. only 180 class bullets i have shot were 185gr berger classic hunters. i think they were in the 2950-3000 ballpark.
500yds and in there is no shot i would take with the 300 that i would not take with a 22in 30-06 if that makes sense.

 

[B23]

Not exactly same same but close enough and will provide some good reading for you.

My 300 WSM AKA (THE PUG)

I wanted to build a short-barreled suppressed 300 WSM for a while. This will be a work in progress. I will be trying a few different suppressors, brass, and powders. The bullet I want to use is the Berger 200x20. I named the project the pug because is short and ugly. HAHA. Here are the specs at...

www.rokslide.com

 

[jlaner0408]

OP- I’m pretty sure Colton Bagnoli (papwinkle on Instagram and the shooting editor for the western hunter) is in the middle of building a 20” suppressed 300 wsm at the moment if you want to stay tuned into his stuff. Shoot him a message on Instagram if you have it- he’ll respond pretty quickly

 

[TimberHunter]

Something to consider… I shot my 7mm mag with a 26 barrel and 8” suppressor. After two shots I had faint ringing in one of my ears. Compared to shooting my 6.5 creedmoor suppressed, I can shoot that back to back to back to back etc without any ringing in my ears.

So if you’re concerned with the sound reducing ability of a can on a magnum rifle, you may want to reconsider going shorter because it gets louder the shorter the barrel is. Now of course a can on any length barrel greatly reduces the noise compared to no cam


Sent from my iPhone using Tapatalk

 

[archp625]

I’m in the process of building a 20” 300 WSM. I have all the parts minus the stock. I emailed yesterday and I’m still 2 months out on it. I will be shooting 200+ grain bullets and a Omega can.

 

[SlimCreaper25]

Also interested in this as well. Building one on a Defianice Anti XM and a 20” carbon 6 1:9.. make sure it’s throated long!

 

[STAxel]

Is all this still even worth it with Factory Ammo? I don’t handload and I know on every other thread people bring up their load info. Am I screwed with this endeavor if I’m limited to factory ammo?

 

[HuntInWild88]

Something to consider… I shot my 7mm mag with a 26 barrel and 8” suppressor. After two shots I had faint ringing in one of my ears. Compared to shooting my 6.5 creedmoor suppressed, I can shoot that back to back to back to back etc without any ringing in my ears.

So if you’re concerned with the sound reducing ability of a can on a magnum rifle, you may want to reconsider going shorter because it gets louder the shorter the barrel is. Now of course a can on any length barrel greatly reduces the noise compared to no cam


Sent from my iPhone using Tapatalk

Not sure what suppressor you have. But I shoot a 7mag 24" Barrel 7.5" form 1 suppressor and have zero ringing after several shots.
When shooting at game you really don't hear it at all. Where as when I just had a break on it it felt like being punched my Mike Tyson.

 

[HuntInWild88]

7mm Remington Magnum (7 Rem Mag) Barrel Length Versus Velocity

7mm Remington Magnum (7 Rem Mag) Barrel Length Versus Velocity Since its introduction in 1962, the 7mm Remington Magnum (7 Rem Mag) has developed a strong following, becoming the most popular metri…

rifleshooter.com

Interesting article. I know this is for a 7mag but still worth a read. I'm actually about to cut my 24" Barrel down to 20"

 

[mississippilpj]

I think the short mag will do a lot better suppressed

 

[762 ULTRAMAGA]

I think the short mag will do a lot better suppressed

Absolutely
I have a 22" 7 wsm throated for 180s that gets 3000fps, and 2875 with 195 eols
RL26 of course

 

[Sled]

Is all this still even worth it with Factory Ammo? I don’t handload and I know on every other thread people bring up their load info. Am I screwed with this endeavor if I’m limited to factory ammo?

I load when needed but find factory ammo to be quite a bit better than it used to. About 3 years ago I ran factory ammo in several bolt guns with short barrels. Still pleased with the results but probably a bad time to quit reloading.

 

[STAxel]

Anyone else?

 

[LRshooter6.5]

OP - what did you end up doing? Thinking of doing the same with a 300wsm at 22" with a gunwerks 6ix+ suppressor.

 

[Mangata]

22” Ace with AB raptor 8 shooting 185 Jugg @ 2970.
Super pleased with performance out to 650

 

[Judd]

Mine is 24" and I really think 20" would be perfect. Saying that, I built mine for speed for an axis hunt a few years ago...it's pushing Lapua 155 Scenars @ 3260. Nothing has went over about 30y that it's been run through. Longest shot to date, 356y and it was that axis I built it for. Been in the safe a couple years without a scope on it. I think I need to pull it out and put a scope on it or sell it. I ran an original Nomad on it.