7mm PRC Build with a 20" Barrel - Elk Rifle for 2024 - Advice?

ID_Matt

WKR
Joined
May 16, 2017
Messages
1,547
Location
Southern ID
Reviewing all these options from the thread here’s where I’m landing based on all the great feedback. Please continue to share your thoughts as this has been extremely helpful. Note, with further researching 1) I’m not as sold on the 700 clone action and Tikka would be nice 2) I’m more sold on the hnt26 chassis immediately rather than waiting 3) A compromise of a 22” barrel is okay… would still like a 20” though.

Here is a comparison of buy/build options… missing anything? Better deals on components out there or alternatives?


BUILD option…

Action, bolt, trigger: Tikka TX3, $655
https://jaoutdoors.com/product/t3x-magnum-long-action-2/

Bolt Handle: Lumley titanium black with intermediate carbon fiber knob, $65

https://lumleyarms.us/titanium-bolt-handles/t3-t3x-superlite-bolt-handle

Barrel: Tikka Proof Research 22” $939
https://jaoutdoors.com/product/proof-research-tikka-carbon-fiber-pre-fit-barrels/

Chassis: HNT26 $1699

https://mdttac.com/hnt26-chassis-system/

Rail: $50?

Magazine: $80?

Labor: $500?

Estimated cost = $4000 before suppressor, scope, and scope rings.


VS BUY option…

Weatherby Model 207 Alpine, $2999
https://weatherby.com/store/model-307-alpine-mdt/

Estimated cost = $2999 before suppressor, scope and rings which would be same regardless of build.

Or of course the Proof Research Elevation MTR previously mentioned at $3800 but does not have a <24” barrel or the foldable chassis.
You can get the HNT26 with an arca rail, if that is what the $50 was referring to. I am probably in the minority, but I'd get a blank and have a good gunsmith chamber the barrel over a prefit just to hopefully avoid any headaches.
 
OP
C

cwpepper

Lil-Rokslider
Joined
Sep 15, 2020
Messages
168
Location
Bend, Oregon
You can get the HNT26 with an arca rail, if that is what the $50 was referring to. I am probably in the minority, but I'd get a blank and have a good gunsmith chamber the barrel over a prefit just to hopefully avoid any headaches.
I am looking for a picatinny rail between the action and the scope rings. Not sure what one to get with a Tikka and what the cost would be at this time.
 

ID_Matt

WKR
Joined
May 16, 2017
Messages
1,547
Location
Southern ID
I am looking for a picatinny rail between the action and the scope rings. Not sure what one to get with a Tikka and what the cost would be at this time.
Look in to the new UM scope rings that are direct mount. There is a thread on here about them!
 

rockymtnsam

Lil-Rokslider
Joined
Apr 30, 2023
Messages
133
I had one built like that for elk this year… we’ll see how it goes.

38a4db62a190b0adbba36a38dd3d146d.jpg



Sent from my iPhone using Tapatalk Pro
Nice looking setup! What’s the build on this?
 

todd458

FNG
Joined
Jun 16, 2023
Messages
39
I had one built like that for elk this year… we’ll see how it goes.

38a4db62a190b0adbba36a38dd3d146d.jpg



Sent from my iPhone using Tapatalk Pro
Hill country rifles. is a company that a couple of friends have used out of new Braunfels Texas for quite a few years. I have a proof tundra that is a phenomenal rifle, but went with Hillcountry on the 7 mm PRC at the advice of these two friends, I was skeptical, if for no other reason the action. Defiance versus Tika. Of course Hill country will build you one with the defiance, they’ll build you anything you want. However, they do offer the Tika action and after talking to Matt at Hillcountry, listening to testimonies, and seeing the rifle shoot, I took a gamble. And could not be happier.
 

Attachments

  • 902FC5E8-356F-4568-8A13-D371FDCDD57B.jpeg
    902FC5E8-356F-4568-8A13-D371FDCDD57B.jpeg
    134.7 KB · Views: 252
  • 4FE9D7CE-E46B-41C3-920B-E23AB8E96B9A.jpeg
    4FE9D7CE-E46B-41C3-920B-E23AB8E96B9A.jpeg
    467.8 KB · Views: 246
  • AFED2F8C-24D6-4155-8E3E-4439DB92BD65.jpeg
    AFED2F8C-24D6-4155-8E3E-4439DB92BD65.jpeg
    274.8 KB · Views: 224
  • 2A01D3BB-ACAD-468E-A51A-7C9DABBF62A2.jpeg
    2A01D3BB-ACAD-468E-A51A-7C9DABBF62A2.jpeg
    124.3 KB · Views: 187

SloppyJ

WKR
Joined
Feb 24, 2023
Messages
1,693
I'm still wondering why a 7PRC if you're going to chop it to 20"? Why not look at something more efficient? A 280AI comes to mind with the same bullet and probably opens more doors for you.
 

todd458

FNG
Joined
Jun 16, 2023
Messages
39
It’s not gonna have the velocity of the PRC in a 20 inch barrel. I don’t believe. Study the two cartridges. Then make a decision. 2877 ft./s with a 162 grain bullet out of a 20 inch barrel it’s pretty impressive.. only 25 rounds down the barrel so I’m being told I could expect anywhere from 30 to 75 feet increase at 100 rounds. We will see.. 2877 ft./s and a 162 gr. .0316 bc will fly forever. I think you would be shocked at when that bullet gets below 1800 ft./s. Just can’t recall.
I want to say 850 yards.
 

SloppyJ

WKR
Joined
Feb 24, 2023
Messages
1,693
It’s not gonna have the velocity of the PRC in a 20 inch barrel. I don’t believe. Study the two cartridges. Then make a decision. 2877 ft./s with a 162 grain bullet out of a 20 inch barrel it’s pretty impressive.. only 25 rounds down the barrel so I’m being told I could expect anywhere from 30 to 75 feet increase at 100 rounds. We will see.. 2877 ft./s and a 162 gr. .0316 bc will fly forever. I think you would be shocked at when that bullet gets below 1800 ft./s. Just can’t recall.
I want to say 850 yards.
I think you'll be within 100 to 125fps with about ~8gr less powder. That's a win in my book for this application but I get that it's not as "sexy" or trendy.
 

todd458

FNG
Joined
Jun 16, 2023
Messages
39
280 AI great cartridge as well. I just think it needs the 24 inch barrel. Almost pulled the trigger on one of those. I don’t know if I would’ve have said its a sexier cartridge.😉
 

Zvestal

FNG
Joined
Jul 27, 2019
Messages
88
Not much of a poster here, more of a poser, I mean, watcher/reader/learner. I'm happy to avoid all the debates: carbon vs steel, folding vs. rigid, what the pros use vs. what actually works, chassis vs. traditional, 20" vs 26", suppressor vs brake vs nothing, etc. So feel free to not light me up over my choices.

BUT for the sake of it I thought it was coincidental that OP was looking at something quite like what I just built. Tikka LA, HNT 26 folder, CarbonSix 18", 6.5 PRC, Gunwerx 6IX, Steiner T6Xi. It's 10lbs 13.7 oz fully dressed, could shave 5oz by doing a modified Magpul magazine (there's a poster here who cut one to fit the Tikka LA inlet) and another 6 oz with a Ti suppressor. It started life as a Tikka T3x Superlight in the Alpine Veil color, then I got ideas.

Don't ask me the cost, I don't math and I'm trying to forget. Cheers to Black Canyon Customs & Fritz for the barrel swap.

Zeroed but not load developed yet. Looking at Hammer Hunter 124gr, should be quick ish I hope.

IMG_2681.JPEG
 

Gadjet

Lil-Rokslider
Joined
Dec 16, 2018
Messages
299
Not much of a poster here, more of a poser, I mean, watcher/reader/learner. I'm happy to avoid all the debates: carbon vs steel, folding vs. rigid, what the pros use vs. what actually works, chassis vs. traditional, 20" vs 26", suppressor vs brake vs nothing, etc. So feel free to not light me up over my choices.

BUT for the sake of it I thought it was coincidental that OP was looking at something quite like what I just built. Tikka LA, HNT 26 folder, CarbonSix 18", 6.5 PRC, Gunwerx 6IX, Steiner T6Xi. It's 10lbs 13.7 oz fully dressed, could shave 5oz by doing a modified Magpul magazine (there's a poster here who cut one to fit the Tikka LA inlet) and another 6 oz with a Ti suppressor. It started life as a Tikka T3x Superlight in the Alpine Veil color, then I got ideas.

Don't ask me the cost, I don't math and I'm trying to forget. Cheers to Black Canyon Customs & Fritz for the barrel swap.

Zeroed but not load developed yet. Looking at Hammer Hunter 124gr, should be quick ish I hope.

View attachment 570498
Very cool build! Any idea what velocities you're getting with the 18 inch barrel?
 
Top