7 PRC Powder

[Bleeb]

I didn’t notice any unburnt powder left behind in the suppressor, but according to GRT I’m around 94% burned.

I don’t disagree with your logic though on using something quicker for a more complete burn. Post your results and let us know how it goes!

How did you get 7 PRC in GRT? My updated version doesn't include it. Are you using a predecessor wildcat?

 

[TxLite]

How did you get 7 PRC in GRT? My updated version doesn't include it. Are you using a predecessor wildcat?

There was a download for it on discord.

You can also take a 7 blaser mag and tweak the specs if you’re up to it.

 

[Bleeb]

There was a download for it on discord.

You can also take a 7 blaser mag and tweak the specs if you’re up to it.

Thanks. I can't seem to login to the GRT discord server because it says my email is already registered and I can't verify it. Geez!

 

[philcox]

@TxLite Any chance of getting a read on powder burn for my current 7PRC load? 168LRX 67.5 g RL 26, 2974 fps, 20” barrel

I’m just curious

 

[TxLite]

@TxLite Any chance of getting a read on powder burn for my current 7PRC load? 168LRX 67.5 g RL 26, 2974 fps, 20” barrel

I’m just curious

Obviously this is just going to be a rough estimate without knowing case capacity and seating depth. This is at 3.34”




To get to your velocity, it’s showing 3.22” COAL with a 96.8% burn rate @ 70,471psi

 

[Bleeb]

Obviously this is just going to be a rough estimate without knowing case capacity and seating depth. This is at 3.34”

View attachment 692518


To get to your velocity, it’s showing 3.22” COAL with a 96.8% burn rate @ 70,471psi

Is there any way you, or anyone else, could send me the 7 PRC update file for GRT? I am getting nowhere with the Discord support bot. I registered in 2018, but did not verify my account, and can't do it now because I don't remember my password from 6 years ago. Like Elvis, I'm caught in a trap.

 

[TxLite]

Is there any way you, or anyone else, could send me the 7 PRC update file for GRT? I am getting nowhere with the Discord support bot. I registered in 2018, but did not verify my account, and can't do it now because I don't remember my password from 6 years ago. Like Elvis, I'm caught in a trap.

pm'd

 

[philcox]

Obviously this is just going to be a rough estimate without knowing case capacity and seating depth. This is at 3.34”

View attachment 692518


To get to your velocity, it’s showing 3.22” COAL with a 96.8% burn rate @ 70,471psi

Thx. I’m sitting at 3.20 COAL, ADG brass. so that’s probably pretty close. A dumb question, is that burn rate decent for my set up, or low? Is there anything I can do to improve it? Or should I even care?

 

[TxLite]

Thx. I’m sitting at 3.20 COAL, ADG brass. so that’s probably pretty close. A dumb question, is that burn rate decent for my set up, or low? Is there anything I can do to improve it? Or should I even care?

100% is obviously ideal, but I think I read somewhere if you are above like 92% or something you are fine.

If it is shooting good with decent velocity spreads, I wouldn't worry about it personally.

 

[jeetS]

Im gonna be placing a powder order in the next month for some 7prc brass...
Feel free to make some powder and load recommendations!

planning on 175g eldx and a 24" barrel

 

[BossGobbler2024]

Im gonna be placing a powder order in the next month for some 7prc brass...
Feel free to make some powder and load recommendations!

planning on 175g eldx and a 24" barrel

There are quite a few posts on 7 PRC loads on here. I have used H1000 with the best accuracy results with both 168 LRX and 175 ELDX bullets but have also tried varies powders including IMR4350 with 150 gr TSX with excellent accurate loads. I didnt have as much success with ABLR bullets in my 7PRC with short 18 inch barrel but H1000 and N570 were OK.