6mm /.243 hunting success on Big Game

[NWBLKTAIL]

Super varmint! What powder you using?

With that much barrel I’d be inclined to try H1000

 

[MT-nuffgun]

Super varmint! What powder you using?

H4831SC

 

[Steve300xcw]

Unless you’re going through a state that requires them.

That would be a PITA. I'd move

 

[minas stiris]

I’ve harvested a lot and seen a lot of deer killed with a 243, and the .257 is just as deadly. The only thing I would suggest is to up the 243 to a 100 or 105 grain bullet. I like 117 in the 257. IMR 4350 works well in both.

 

[mxgsfmdpx]

Kill 3 with the Tikka 6 Creed and 115 Berger tonight, on a large whitetail buck.

Yardage: 183.
Impact Velocity: Roughly 2,300
Shot Position: Seated Supported
Distance travelled After Hit: 20 yards.
Impact Location: Entered and broke 4th/5th ribs. Bullet recovered in offside shoulder.

 

[24valve]

@Small-foot's Mule deer buck shot at 2400 impact velocity with 95 TMKs.

Buck ran 40-50 yards after being hit, then collapsed and did not move after 10-15 seconds on the ground.

Large entrance wound, made soup of the vitals, and the jacket was found in the offside hide. The lead core passed all the way through and made a smaller exit wound.

Faster time time to incapacitation and less drama than smaller bucks shot with a 6.5 creedmoor and 300 win mag in the two days prior to this one.

 

[OneEyedGopher]

Hit em where you’re supposed to and they’re not gonna like it. No need to over think it

 

[BugDance29]

Tikka .243 1:8 twist, shooting 108 eldm’s from Unknown Munitions. Barrel chopped to 16.5 inches with a suppressor. Shot this buck at 125 yards just in front of the shoulder and had an exit wound out the offside neck. Massive internal damage. Buck dropped instantly.

View attachment 961851

How are you liking your shorter barreled 243 with a can? Is it suppressing well? I’ve been contemplating having my .243 RA Standard (22”) cut to somewhere near 16 or 18” and threaded, but wasn’t sure how much of a pain it would be considering the thin barrel profile. Did you have to go with 1/2x28?

The temptation to buy a new rifle (6 ARC) that is already threaded is looming over my head, but the ole girl shoots NBT’s into cloverleafs and fills my freezer every time I squeeze the trigger.

 

[Blueman75]

How are you liking your shorter barreled 243 with a can? Is it suppressing well? I’ve been contemplating having my .243 RA Standard (22”) cut to somewhere near 16 or 18” and threaded, but wasn’t sure how much of a pain it would be considering the thin barrel profile. Did you have to go with 1/2x28?

The temptation to buy a new rifle (6 ARC) that is already threaded is looming over my head, but the ole girl shoots NBT’s into cloverleafs and fills my freezer every time I squeeze the trigger.

I’m loving it so far. My Tikka has the D18 barrel, so I had it threaded 5/8x24. The can definitely gets rid of the crack of the shot. I’ll probably pick up a 6 Creedmoor when Tikka finally releases them so I can shoot factory 108 eldm’s.

 

[fshaw]

Is anyone shooting the 95gr TMKs in a 10” twist gun with success? I see that Sierra has them marked for a 9” twist. Thanks.

 

[Formidilosus]

Is anyone shooting the 95gr TMKs in a 10” twist gun with success? I see that Sierra has them marked for a 9” twist. Thanks.

@Small-foot is. Post 2,366 on this page shows her last kill with it.