6 PRC reloading

[Titanmoose]

How are folks making a modified case for the 6 PRC? I assume a mandrel on the higher end of the caliber or the bottom of the next up but I’m unsure. I assume necking down a 6.5 Hornady modified case then a mandrel but curious what works. Would prefer not to buy another mandrel for 1 use

 

[mddat]

No need to make a modified case. I disassemble the bolt and remove the plunger, then seat a bullet long and slowly start seating the bullet down till there is no resistance when closing the bolt. Here’s a link to Alex Wheeler web site with a video. Look for finding your lands video

Videos | wheeleraccuracy

www.wheeleraccuracy.com

 

[Titanmoose]

No need to make a modified case. I disassemble the bolt and remove the plunger, then seat a bullet long and slowly start seating the bullet down till there is no resistance when closing the bolt. Here’s a link to Alex Wheeler web site with a video. Look for finding your lands video

Videos | wheeleraccuracy

www.wheeleraccuracy.com

pretty useful way of doing it.

 

[JBahr]

I'll do a full writeup on my setup once it's done but some promising results so far...
Pressure reached here: 109 ELDM, 61 grains N570, CBTO 2.348", 0.010" Jam in the Lands, COAL 2.941", 215GM Primer
Load the rifle liked the most, so far: 109 ELDM, 61 grains N570, CBTO 2.328", 0.010" Jump off Lands, COAL 2.921", 210GM

 

[2buffalo]

I'll do a full writeup on my setup once it's done but some promising results so far...View attachment 845417
Pressure reached here: 109 ELDM, 61 grains N570, CBTO 2.348", 0.010" Jam in the Lands, COAL 2.941", 215GM PrimerView attachment 845419
Load the rifle liked the most, so far: 109 ELDM, 61 grains N570, CBTO 2.328", 0.010" Jump off Lands, COAL 2.921", 210GMView attachment 845422

How long is your barrel?

 

[JBahr]

How long is your barrel?

22" Ace, SP3 Contour, Wrought Iron Fluting

 

[2buffalo]

61.5g N570
115 DTAC
3261 fps avg over 24 shots
20" barrel
Had better accuracy with H1000 going to try dropping .5g if it doesn't work I will be going back to H1000.

 

[Runolfson]

Got my barrel from PBB and assembled rifle. Headspace was good but the dummy round was tough to close bolt on and hard to eject. Looking at bullet looks like rifling scratches in the area that should be in the freebore. I suspect a worn out reamer cut my chamber. Disappointing for sure.

Anybody else have this problem before? What did you do?

 

[GoatPackr]

Got my barrel from PBB and assembled rifle. Headspace was good but the dummy round was tough to close bolt on and hard to eject. Looking at bullet looks like rifling scratches in the area that should be in the freebore. I suspect a worn out reamer cut my chamber. Disappointing for sure.

Anybody else have this problem before? What did you do?

I'd call them and let them know.
Ask them to pay shipping also.

 

[wind gypsy]

Got my barrel from PBB and assembled rifle. Headspace was good but the dummy round was tough to close bolt on and hard to eject. Looking at bullet looks like rifling scratches in the area that should be in the freebore. I suspect a worn out reamer cut my chamber. Disappointing for sure.

Anybody else have this problem before? What did you do?

I've seen borescope pics from a PBB barrel that had freebore cut to a smaller diameter than the depth of grooves thus you could see rifling in the freebore. That was in a PBB thread over at LRH and it seemed like PBB resolved it reasonably so I'd give em a call and see what they say.

Do you have a bore scope?