2025 Mathew’s Bows

Joined
Sep 11, 2017
Messages
1,344
Location
Bozeman, MT
I was asking it rhetorically.


You adjust it it by moving, and the point of everything I have said is I'm not certain this system as it is will provide enough movement as it is.


You don't need a laser to measure it, just a straight edge.

My point is simple. If you start a bow build/arrow tune with a properly set up bow and a properly spined arrow, you won’t need to move the cams very much at all. You don’t need massive amounts of movements if you’ve done everything else correctly.

Starting with parallel cams is quite important in this process.


Sent from my iPhone using Tapatalk
 
Joined
May 6, 2018
Messages
9,714
Location
Shenandoah Valley
My point is simple. If you start a bow build/arrow tune with a properly set up bow and a properly spined arrow, you won’t need to move the cams very much at all. You don’t need massive amounts of movements if you’ve done everything else correctly.

Starting with parallel cams is quite important in this process.


Sent from my iPhone using Tapatalk

My point is after tuning a good number of Mathews with the Top Hat system, and the range some of them have needed to shift from how they came from factory, I'm wondering if this system has enough adjustment without needing to change the one top hat some. Wouldn't be drastic, and probably not common, but no more change in cam lean that I saw with the 2 I played with, I think it might need to be done some.

It might be they really have limb deflection dialed in now, and it's extremely consistent. Putting 2 limbs together to make one you can probably get the tolerances tighter, if they are doing that. Might be they are just grabbing individual limbs out of a barrel, and you could have two weaker limbs paired up and two stiffer limbs, kinda stacking tolerances.
 
Joined
Sep 11, 2017
Messages
1,344
Location
Bozeman, MT
My point is after tuning a good number of Mathews with the Top Hat system, and the range some of them have needed to shift from how they came from factory, I'm wondering if this system has enough adjustment without needing to change the one top hat some. Wouldn't be drastic, and probably not common, but no more change in cam lean that I saw with the 2 I played with, I think it might need to be done some.

It might be they really have limb deflection dialed in now, and it's extremely consistent. Putting 2 limbs together to make one you can probably get the tolerances tighter, if they are doing that. Might be they are just grabbing individual limbs out of a barrel, and you could have two weaker limbs paired up and two stiffer limbs, kinda stacking tolerances.

I suppose it could happen…i guess I’m willing to take the plunge based on Mathew’s QC in the past. I would think that would become a warranty issue if so.


Sent from my iPhone using Tapatalk
 
Joined
May 6, 2018
Messages
9,714
Location
Shenandoah Valley
I suppose it could happen…i guess I’m willing to take the plunge based on Mathew’s QC in the past. I would think that would become a warranty issue if so.


Sent from my iPhone using Tapatalk

I mean, I was pleased with how easy it was to pull the axle. So changing yokes aren't really anymore complicated, just will need to reference where the axle position was, but the donut placement tends to slightly change cam lean anyways.

I feel really certain that a shop should be able to check cam lean, change the TH if necessary (doubtful, but maybe a few) and the customer can take it home and tune it.
 

ddowning

Lil-Rokslider
Joined
Jul 12, 2023
Messages
287
I wrote that review; my mod screws were blue loctite in and not loose. It took heat and a LH drill bit to get out.

The cable being cut is the issue that should have been caught in design/engineering if that bow couldn't stay on track at max DL and the cams shimmed over.
The rx8u is at the 30.25" position right now which is the bottom of the longest mod. I was thinking about twisting cables to go back to the top of the 30" mod for more speed, but maybe that isn't such a great idea.
 

sndmn11

"DADDY"
Joined
Mar 28, 2017
Messages
10,400
Location
Morrison, Colorado
I went and shot the 33 liftX and it was nice. They had 60# mods in 30"/30.5/31" 85%, which was a surprise. I expected to turn down a 70lb bow and be told other mods were an unknown ETA.
 
Joined
May 6, 2018
Messages
9,714
Location
Shenandoah Valley
I went and shot the 33 liftX and it was nice. They had 60# mods in 30"/30.5/31" 85%, which was a surprise. I expected to turn down a 70lb bow and be told other mods were an unknown ETA.

Mods are same as they have been, nothing new.

Shops should have a good supply by now.


Only thing different is on the RS, I think it's a same part number, but different # depending on limbs. Or something like that.


Tho the XD or whatever the long draw bow is does have a different cam, but still takes same mods.
 

3forks

WKR
Joined
Oct 4, 2014
Messages
885
I shot a 33 Lift X at 70 pounds at 31”, at 85% left-off and I was impressed.

I keep hearing that the draw cycle on the bow is stiff at the beginning, and has a more pronounced dump into the valley, but I didn’t notice that. The draw felt very smooth and linear to me.

I’ve been shooting Hoyt Ultras for a few years and have no complaints, but that Mathews has made me consider it.

The only thing I wish Mathews had was a 75% let-off. I’ve seen comments on line where people say the cam is jumpy at 80%, but that’s hard to believe. At 85%, it was impossible for me to feel that, but I can’t imagine that cam being jumpy even at 80%. Maybe.

I’ve heard it’ll be mid-March before any bow that you order will show up, and I’m not sure what module availability would be for what I’d need, but I’m considering placing an order.
 

Pramo

WKR
Joined
Jan 13, 2015
Messages
450
Location
Westminster, MD
I moved from a Rx7 ultra to a lift last year, honestly I can think of a better bow, it’s light fast and predictable. I just bought a second lift 33 and gonna unload my Ultra.

The draw is fine using 80 or 85% left off, the cables stretch/settle a good bit both Mathews match and gas strings and they had the limb splinter problem. No bows blew up and I have had all kinds of splinters over the years on bows I wasn’t worried

The other downside to the Lift is a little finicky on top hats, I bought the podium ones so I don’t have to move the rest. The new tuning system should fix this
 
Top