Whats your reloading process?

[Johnc427]

1. Remove primers (for even measurements)
2. Wet Tumble brass (only if very dirty)
3. Anneal (every 2-3 firings)
4. Spray with 90/10 alcohol/lanolin
5. Resize brass w/o expander ball (bump shoulder .0015”, .004” NT)
6. Expanding mandrel w/ dry lube (.002” NT)
7. Clean case mouths of dry lube w/ q-tip and neck brush
8. Quick dry tumble (remove case lube)
9. 3 way trim
10. Seat primers
11. Load powder
12. Seat bullets

 

[BBob]

Probably showing my ignorance here, but doesn’t FL sizing stretch the case and possibly put you over max length?

No not necessarily. If you get to or close to max length you trim.

 

[Eric_F]

Probably showing my ignorance here, but doesn’t FL sizing stretch the case and possibly put you over max length?

Not if you use a mandrel instead of an expander ball, so you size on downstroke instead of up. And usually very minor in any case.

 

[MallardSX2]

-Tumble
-Lube
-d-cap & Bump .003<
-Measure
-Trim
-Chamfer
-Cap
-Powder
-Bullet

Boom. Repeat.

I don't anneal. When my brass wears out, I throw it in the trash.
Lifes too short to anneal brass for us non-ribbon chasers imho.

 

[sndmn11]

Fl size
Chamfer
Vibrate in media
Prime
Powder
Bullet

 

[JGRaider]

Collet neck size
Prime
Throw powder
Seat bullet

No cleaning, trimming, annealing, no bullshit

Amen brother.

 

[kthomas]

Mines pretty simple:

- Tumble in rice
- Anneal
- FL size
- Trim/chamfer/deburr
- Prime
- Charge
- Seat bullets

 

[7LRM]

Deprimer
AMP
Lube
Brush inside the neck of brass
Busing dies
Giraud case trim
Cleaning primer pocket
Wet tumbling
Clean and dry
Oven for a few minutes make sure no moisture
Primers
Drop powder
Sitting bullets
And go to the range!

Happy shooting and hunting !

 

[FLShooter293]

This is not the fastest but works for me and I usually only reload 25-50 rifle cartridges at a time. I actually like that this drags out the time as it gives me something to do

Deprime
Measure for HS
SS media wet tumble 2 hours
Anneal in AMP
Size without expander ball using imperial wax
Wet tumble 1 hour
Debur case mouths
expand necks with 21st Century mandrel was using graphite now using Neolube
Prime
Charge
Seat bullet

 

[RidgeRunner1018]

Mine's not too different than others. For simplicity, I follow the same process for hunting rounds as I do my PRS rounds:

• Tumble in walnut media with Flitz
• Anneal w/AMP
• FL size with SAC die. This bumps the shoulder 0.002", sizes the neck and de-primes
• Trim w/Henderson so I have and inside and outside chamfer
• Tumble again to remove the lube
• Prime
• Powder
• Seat bullets

 

[DiabeticKripple]

like many others

- deprime
- wet ss tumble
- dry in oven
- lube
- FL resize with 0.002" shoulder bump (using hornady comparator set)
- wipe lube off with rag and brake cleaner
- trim
- chamfer/deburr
- prime
- powder
- bullet

 

[6MT]

1. De-cap
2. Wet tumble
3. Anneal
4. FL size
5. Prime
6. Charge
7. Seat

I trim only when necessary. Drying after cleaning is done on a cookie tray. Usually overnight.

Easy.

 

[northernalpine]

 

[northernalpine]

In all seriousness:
- Clean
- Decap
- Anneal
- FL resize / .002-.003 bump
- Exp mandrel
- Powder
- Seat
- Shoot

 

[starfish89]

My reloading process is simple.

Dry tumble, deprime, FL size, chamfer/trim, prime, charge, seat.

I streamline my process. No annealing, 1 tumble cycle with no drying, no primer pocket cleaning, no turning, nothing like that.