Welcome Exterra (and shoot for Scope Rings)

[robby denning]

I'll be at the Hunt Expo Thursday and Friday, hope to see some of you there

booth #?

 

[Axlrod]

Thank you… except I just realized that your T1X proto looked way nicer than the T1X proto on my rifle… I need to re-evaluate my business plan

Sent from my iPhone using Tapatalk

Very nice looking rings, can't wait to try them. My only advice is, get some hats and stickers to sell on your web site. Then take one of the stickers and put it on the logo on that scope!

 

[Fred@Exterra]

Very nice looking rings, can't wait to try them. My only advice is, get some hats and stickers to sell on your web site. Then take one of the stickers and put it on the logo on that scope!

That’s my beater 22 with some old old prototypes

Surprisingly, that scope has held up pretty well & it’s had a hard life.

Here’s a better representation:

Sent from my iPhone using Tapatalk

 

[Exterra]

booth #?

No booth this year, just going to enjoy the show.

 

[renagde]

Extra low Tikka rings an option?

 

[chutinlead]

I can really appreciate the use of 7075AL in a mount like this and the shouldered screws.

 

[Fred@Exterra]

booth #?

If you run into Vince at the show make sure you ask about his trip down… it’ll also explain why he showed up to the show covered in mud and blood


Sent from my iPhone using Tapatalk

 

[Fred@Exterra]

Extra low Tikka rings an option?

They are an option, on a special order basis. Send an email to [email protected] & we can discuss your specific application.

Fred


Sent from my iPhone using Tapatalk

 

[robby denning]

If you run into Vince at the show make sure you ask about his trip down… it’ll also explain why he showed up to the show covered in mud and blood


Sent from my iPhone using Tapatalk

Heard the story. Glad that lady‘s OK and he should be EMT

 

[43.6N]

@Exterra welcome to Rokslide. I remember reading about your monolithic rings several months ago on a different thread. So happy to see these come to market!

Here’s three 10 round groups today. One with iron sights lol!

 

[Exterra]

Congratulations on being the first entry. Nice shooting, I love the variety.
Thanks for the welcome and good luck in the drawing.

 

[260284]

First group are 87 V-max out of my 20” LS Wild 6 Creed with my clip on thermal. Second ground are the 76gr TipStrikes out of the same setup. I put a handwarmer on the back side of my gator board target backer.

 

[Fred@Exterra]

#1 shot is from an absolutely clean/cold bore… always a good data point to know, especially when the poor thing hasn’t been cleaned in about 400 rounds


Sent from my iPhone using Tapatalk

 

[Exterra]

First group are 87 V-max out of my 20” LS Wild 6 Creed with my clip on thermal. Second ground are the 76gr TipStrikes out of the same setup. I put a handwarmer on the back side of my gator board target backer.View attachment 1022559View attachment 1022560

Nice shooting, Good luck in the drawing

 

[gtriple]

I’m just happy that you included the height from the top of the rail to the centerline of the scope. That is so much easier to measure than centerline of bore. Well done.

 

[Fred@Exterra]

I’m just happy that you included the height from the top of the rail to the centerline of the scope. That is so much easier to measure than centerline of bore. Well done.

That was my fault

I think we are going to change everything over to top of action to c/l of scope… it’s the industry standard for a reason. We’ll still include c/l of bore to c/l of scope engraved on the front of the mount. Having this number helps when setting up ballistic programs.


Sent from my iPhone using Tapatalk