Ultralight reliable tikka rings?

[Marbles]

On hight:

The T084s are 1.59" center bore to center optic.

For reference:
-UM lows are 1.65" center bore to center optic.
-Area 419 20 MOA rail and NF UL lows are 1.69" center bore to center optic.
-Area 419 20 MOA rail and NF UL mediums are 1.81" center bore to center optic.

 

[Macintosh]

On hight:

The T084s are 1.59" center bore to center optic.

For reference:
-UM lows are 1.65" center bore to center optic.
-Area 419 20 MOA rail and NF UL lows are 1.69" center bore to center optic.
-Area 419 20 MOA rail and NF UL mediums are 1.81" center bore to center optic.

Savage! Thanks. T084’s otw.

 

[Macintosh]

Opened up the TO84’s today. The recoil pin is a chunky roll-pin that does not even come close to fitting in the two smaller recoil pin holes on the t3x action. Yet it also seems awfully small to go in the giant “hot tub” shaped recoil lug recess. Are folks just putting it in the recess and sliding it forward?

Are you all just leaving your threaded rail holes open? Ive long since lost the the little plastic plugs that came in those holes. No biggie, just seemed like a good way to get grit or snow inside.

@Formidilosus

 

[Marbles]

Opened up the TO84’s today. The recoil pin is a chunky roll-pin that does not even come
close to fitting in the two smaller recoil pin holes on the t3x action. Yet it also seems awfully small to go in the giant “hot tub” shaped recoil lug recess. Are folks just putting it in the recess and sliding it forward?

Are you all just leaving your threaded rail holes open? Ive long since lost the the little
Plastic olugs that came in those holes. No biggie, just seemed like a good way to get grit or snow inside.

I have stainless steel grub screws in mine.

 

[Macintosh]

@Marbles , 8-48?

 

[Shortschaf]

6-48
I used the screws as a recoil stop in front of each scope ring rather than the roll pin

 

[Marbles]

@Marbles , 8-48?

These in 6-48.

Slotted Fine Thread Gun Plug Screws - 10 pcs. (#6-48 x 1/8", Stainless Steel): Amazon.com: Industrial & Scientific

Slotted Fine Thread Gun Plug Screws - 10 pcs. (#6-48 x 1/8", Stainless Steel): Amazon.com: Industrial & Scientific

www.amazon.com

I used loctite because my one worry is that they migrate down and bind the bolt.

 

[Formidilosus]

Opened up the TO84’s today. The recoil pin is a chunky roll-pin that does not even come close to fitting in the two smaller recoil pin holes on the t3x action. Yet it also seems awfully small to go in the giant “hot tub” shaped recoil lug recess. Are folks just putting it in the recess and sliding it forward?

Are you all just leaving your threaded rail holes open? Ive long since lost the the little plastic plugs that came in those holes. No biggie, just seemed like a good way to get grit or snow inside.

@Formidilosus

Put the pin in the ring, then slide the pin all the way forward in the large oval shaped recess, tighten.

 

[denverangler725]

@Macintosh Ive also been weighing this exact same question and still going back and forth between Sportsmatch and the Hawkins for my 6CM build. Curious if anyone including @Formidilosus has any guidance as to the ability of these Hawkins rings to maintain zero and being no fuss as the Sportsmatch rings have been for me in the past.

 

[Macintosh]

Put the pin in the ring, then slide the pin all the way forward in the large oval shaped recess, tighten.

Ie the pin takes a dunk in the hot tub. Thank you Sir!

 

[Formidilosus]

@Macintosh Ive also been weighing this exact same question and still going back and forth between Sportsmatch and the Hawkins for my 6CM build. Curious if anyone including @Formidilosus has any guidance as to the ability of these Hawkins rings to maintain zero and being no fuss as the Sportsmatch rings have been for me in the past.

Rings that are screwed onto the action are never as durable or reliable as when mounted directly to the rail.

 

[BCsteve]

Rings that are screwed onto the action are never as durable or reliable as when mounted directly to the rail.

I have Sportsmatch on three Tikka's without issues and I believe you but in my brain that doesn't make sense that clamping power beats two piece of metal screwed together!? Is it a function of the size of the screws?

 

[Formidilosus]

I have Sportsmatch on three Tikka's without issues and I believe you but in my brain that doesn't make sense that clamping power beats two piece of metal screwed together!? Is it a function of the size of the screws?

You believe two tiny 6x48 screws are stronger than a clamp? Not only that, what keeps the base from rotating or moving on them?

 

[Macintosh]

@Formidilosus is the sportsmatch to48 the 1” version of the 30mm to84 height wise? Im not finding dimensions online anywhere. Hoping for same height, definitely not taller.

 

[Formidilosus]

@Formidilosus is the sportsmatch to48 the 1” version of the 30mm to84 height wise? Im not finding dimensions online anywhere. Hoping for same height, definitely not taller.

IIRC they are the same height.

 

[Macintosh]

Thank you Sir

 

[BLJ]

@Formidilosus is the sportsmatch to48 the 1” version of the 30mm to84 height wise? Im not finding dimensions online anywhere. Hoping for same height, definitely not taller.

TO48C are 17mm to the bottom of the ring.
TO84 are 13mm to the bottom of the ring.

From the Sportsmatch website.

 

[BLJ]

Sportsmatch UK | Quality scope mounts and rifle scope rings

The Sportsmatch range of scope mounts offers unparalleled stability and precision. No loss of zero is Guaranteed

sportsmatch-uk.com

 

[Macintosh]

Thanks blj, for some reason my search missed the compny website.
So
To48 17mm + 12.5mm=29.5mm
To84 13mm + 15mm= 28mm

So looks like the 1” rings are a touch higher.

 

[BLJ]

No problem.

I’ve had both side by side and it’s not much, but noticeable.

I can’t remember if I had to make any comb adjustments going from to the other or not.