The Tikka 6.5 Creedmoor Reloading Thread

[Gorp2007]

On that point, would it be possible to swap to the LA bolt catch and use the LA mags to allow for longer COAL? Just a thought, I’ve honestly not researched it.


Sent from my iPhone using Tapatalk

Should work just fine. I put a 6.5 barrel on my 30-06 and use the long action mags. The only issue I ever see is with 5 round mags, sometimes the last round or two doesn’t want to feed.

 

[Stalker69]

Yea but your mag well was already sized for the 30-06 round.

 

[Gorp2007]

Yea but your mag well was already sized for the 30-06 round.

Sorry, didn’t see the part about the TAC A1, that certainly changes things.

If the original question was for a Tikka running standard mags, all the actions and mag wells are built for a long action, so swapping is as simple as a new bolt stop and a LA magazine.

 

[bober90]

Yea, I was assuming the bottom metal was the same on the tac a1 as a standard t3x.


Sent from my iPhone using Tapatalk

 

[bober90]

To clarify, “same” meaning the mag are the same length and the bolt stop determines LA or SA, making the bottom universal. But since the a1 is in a chassis that doesn’t seem to be the case.


Sent from my iPhone using Tapatalk

 

[Ferrulewax]

Old thread, but I'm going to bump it again. new to reloading, new to 6.5cm. Got a 6.5cm tikka on the way and plan to cut it to 18-20" (any suggestions?) and then get to work developing loads. I have done some (a lot) of looking on the forum but would love to see more load data for shorter barrel tikkas.

 

[amassi]

Old thread, but I'm going to bump it again. new to reloading, new to 6.5cm. Got a 6.5cm tikka on the way and plan to cut it to 18-20" and then get to work developing loads. I have done some (a lot) of looking on the forum but would love to see more load data for shorter barrel tikkas.

What bullet/ powder do you want to use?


Sent from my iPhone using Tapatalk

 

[Ferrulewax]

What bullet/ powder do you want to use?


Sent from my iPhone using Tapatalk

147 eldms are the plan if they shoot. I have a decent amount of IMR4350 to play around with (dad does some reloading) but sounds like H4350 is a crowd favorite so I plan to pick some up and may settle on that, but I am open to about anything.

I also have 400 rounds of hornady factory (129grn interlock) ammo that I plan to do some practice, barrel break in, and whitetail hunting with and use those casings to reload.

 

[amassi]

147 eldms are the plan if they shoot. I have a decent amount of IMR4350 to play around with (dad does some reloading) but sounds like H4350 is a crowd favorite so I plan to pick some up and may settle on that, but I am open to about anything.

I also have 400 rounds of hornady factory (129grn interlock) ammo that I plan to do some practice, barrel break in, and whitetail hunting with and then use those casings to reload.

Imr4350 works great, H4350 might be a touch more temp stable.
Factory 22.4” sporter barrel
Hornady brass
147 eld-m
Fed 210
41.5 g IMR 4350
2.790 coal
2685 fps
Shot great


Sent from my iPhone using Tapatalk

 

[Ferrulewax]

Imr4350 works great, H4350 might be a touch more temp stable.
Factory 22.4” sporter barrel
Hornady brass
147 eld-m
Fed 210
41.5 g IMR 4350
2.790 coal
2685 fps
Shot great


Sent from my iPhone using Tapatalk

doesn't get any more applicable than that! thanks for the info! I'm hoping to get 2600+ out of an 18" barrel so sounds like that may be pretty close.

 

[amassi]

doesn't get any more applicable than that! thanks for the info! I'm hoping to get 2600+ out of an 18" barrel so sounds like that may be pretty close.

Should not be an issue at all.
The load I posted had zero pressure signs and would probably be around 2570 from an 18” tikka barrel.
Other or more powder would get you over 2600.


Sent from my iPhone using Tapatalk