SilencerCo Scythe Ti failures

[HighUintas]

I'd like to know how many of the failures logged on rokslide are from a decent amount of hand loads that are too hot.

 

[waspocrew]

I’d wager the actual failure rate is much lower than 10%. That would be a huge issue for SiCo. I just got my can this week. Only tested a few rounds on my 22” 300 PRC and it sounded great. Probably won’t be used on that rifle much so I’m not too worried about it.

It would be nice if SiCo was more transparent about the issue though and just put some damn barrel length restrictions on it like any other can.

 

[HighUintas]

Someone shooting something "big" on a short barrel that has blown it up should continue to hammer rounds through it after the warranty fix. I'd like to see if there's repeat failures.

All I've got is a 22" 243 and 16" 223.

 

[Foster_65]

I'd like to know how many of the failures logged on rokslide are from a decent amount of hand loads that are too hot.

I can tell you that mine are hand loads but are not hot. I’ve rarely ran this can hot enough where it was too hot to touch. And that not many rounds especially with 300 prc. The most it took was a 5 shot string then cooled. I almost always only shoot no more than 5 shots before cooling unless it on a ln arc or something. In failed on the third or 5 shots on a 20 in 280 AI. If it can’t handle that, I don’t want it. This was surely a product failure and I wish I could get out from under it and pick up something else which is a shame cuz I like the can. My serial number is around 7000 if that has anything to do with anything. Hopefully his get fixed and never happens again but if I can’t shoot it on a 20 in anything other than maybe a rum, I’m not interested.

 

[Raghornklr]

Someone shooting something "big" on a short barrel that has blown it up should continue to hammer rounds through it after the warranty fix. I'd like to see if there's repeat failures.

All I've got is a 22" 243 and 16" 223.

I'm putting mine right back on the same rifle and was wondering the same thing. Hoping the fix really fixed it.

 

[waspocrew]

I think that’ll be the real test - does it fail again on the same rifle?

 

[HighUintas]

I have run mine fairly hot (not hand loads but the can temp). I have been planning to see what temp I actually get it up to but can't seem to remember my multimeter when I go. I always slide the cover back and check temp with my hand. If I can't touch it momentarily then I let it cool.

No failure yet but I'm not going to baby it. If it's going to fail I want it to fail outside of a hunting trip

800F is hot enough to burn the absolute shit out of your hand if you touch it

 

[TxLite]

If it's going to fail I want it to fail outside of a hunting trip

I’ve been running some longer strings (10-15 rounds for the non mags, 10 on the prc) on mine lately to test it for this exact reason. 16” 233 (bolt gun with a stiff load of tac on 77 tmk), 11.85” 223 (AR with same load), 18” 7prc (definitely loaded hot), 18” 6mm creed.

 

[Legend]

Someone should pull together the serial numbers of all the failures. It would be interesting to know if there is any corelation. Maybe we are past the issue....or not.

 

[HighUintas]

What's the SN format for these? Mine is SYT30xxxx. Is the last 4 the SN?

 

[HuntHarder]

Hot handloads or not, it is almost huge cause for concern if it's that close to failure on each shot... So far, mine has around 1k rounds thru it. Mainly 6.5 bitchbiscuit in a 20", but also around 150 rds of 300 win. In 22". No failures yet, knock on wood