SAC Nexus Press / Inline Fabrication Mount

[Shooter Mike]

Does anyone have a Nexus press mounted on an in-line fabrication quick change mount? If so, is it drilled out for the primer drop tube, and is it stable/solid enough? I currently have a quick change mount on my bench, and would like to continue to use the quick change system; however, if it’s not stable enough, I will just go with a dedicated amount.
Thanks!


Sent from my iPhone using Tapatalk

 

[TEWONG]

I have one mounted to a 4" Micro Ultramount. It does have the hole predrilled for the primer drop tube. Very solid.

 

[Shooter Mike]

I have one mounted to a 4" Micro Ultramount. It does have the hole predrilled for the primer drop tube. Very solid.View attachment 725068

Thanks. Is that a quick change or dedicated mount?


Sent from my iPhone using Tapatalk

 

[TEWONG]

It's a quick change. Makes swapping between press and Henderson trimmer a breeze.

 

[Shooter Mike]

It's a quick change. Makes swapping between press and Henderson trimmer a breeze.

Perfect. Exactly what I needed to know


Sent from my iPhone using Tapatalk

 

[Shooter Mike]

So the new press showed up yesterday. Got it setup this morning when I got home from work, and loaded up some more 7 PRC test loads. I started out with a XL-750 and piked up a FA F1 and M-Press for single stage work. I realize I don't know what I don't know yet, but I think this is the easiest so far to get consistent results with the least amount of effort. Really surprised with the mechanical geometry of this- very little effort for raising and lowering the ram. I took the primer catch off the F1 and drilled it a little larger to slip over the primer tube on the Nexus. The threads are still intact in the F1 primer catch, so it can be swapped back and forth. I'll likely use the F1 for handgun loads, until SAC comes out with shell holders for handgun cartridges and 45-70.

 

[Shooter Mike]

I'm not totally bought-in on the efficacy of low concentricity, but FWIW, using my same dies, my concentricity is ~0.0015" as compared to ~0.004" with the F1 and M-Press when using the FA Universal Seating Die.

 

[Luvhuntingelk]

Looking good, i ordered my Nexus in Feb and still waiting on it to show up

 

[Shooter Mike]

Looking good, i ordered my Nexus in Feb and still waiting on it to show up

I ordered from Brownells. Shipped the next day. MidWay USA has them in stock too.


Sent from my iPhone using Tapatalk

 

[Luvhuntingelk]

I ordered from Brownells. Shipped the next day. MidWay USA has them in stock too.


Sent from my iPhone using Tapatalk

Yes I know. I’ve shared my feelings about how SAC have sold these presses and allowed “pre-orders” direct to customer than favored the big box stores. Midway even had a 10% off deal recently on reloading equipment and Nexus was a part of the sale.

To top it off, SAC has a restocking fee to cancel my preorder. Ironic since they don’t have it to restock.

Poor decision on their part and it certainly screwed over their customers

 

[Shooter Mike]

Yes I know. I’ve shared my feelings about how SAC have sold these presses and allowed “pre-orders” direct to customer than favored the big box stores. Midway even had a 10% off deal recently on reloading equipment and Nexus was a part of the sale.

To top it off, SAC has a restocking fee to cancel my preorder. Ironic since they don’t have it to restock.

Poor decision on their part and it certainly screwed over their customers

Yeah that is kinda shitty on their part. Maybe call them?? Brownells had 10% off at the time too, which is why I ordered there.
I hope it works out for you and you get the press soon.


Sent from my iPhone using Tapatalk