RokStok

[Nine Banger]

Pachmyer has several styles, which model/type would you recommend?

Post in thread 'RokStok'

Sep 28, 2025

If you need just a little LOP added like I did (to get the Maven to work with recoil pins) this Pachmayer pad is pretty close and if you're not after perfect the grinding is pretty easy. I've been putting it off and I'm sitting here waiting for a kid to show up to go hunting tonight and I knocked it out in a few minutes.

Observe the slight lip that isn't covered with the factory screw holes.

Pachmayr 752B Old English Grind to Fit Recoil Pad 1 Thick Medium Black

These pads have a unique rounded edge design, a "leather-look" face with black base and a skeletonized internal bottom core design. For...

www.midwayusa.com

• Nine Banger

• 

 

[longrangelead]

Pachmayer 752B small fits the Rokstok. comes in .6", .8" and 1" thick.

The 752B of all sizes have a metal frame according to each size so you can only grind about 3/16" in from any side.



The Pachmayer 500B and decelerator youth/xs fit the Lite.
The 500B is .5" thick, no frame.
The Decelerator youth is 1" thick and has washers around the screw holes, no frame.



Btw- Brownell's is out of the 500B/youth...

 

[WOOD5045]

Pachmayer 752B small fits the Rokstok. comes in .6", .8" and 1" thick.

The 752B of all sizes have a metal frame according to each size so you can only grind about 3/16" in from any side.

View attachment 1019221

The Pachmayer 500B and decelerator youth/xs fit the Lite.
The 500B is .5" thick, no frame.
The Decelerator youth is 1" thick and has washers around the screw holes, no frame.

View attachment 1019222

Btw- Brownell's is out of the 500B/youth...

Awesome, thank you sir! Just ordered two 752B's and some Pachmayr spacers to play with LOP.

 

[khuber84]

That pacamery 500B is my favorite pad. Firm, no squish or sideways give. I put em on everything.

 

[passinggas33]

Since I’ve never done a grind to fit, what is the weapon of choice for the grinding? Belt sander? Disc sander? Sandpaper by hand? Or am I making this harder than it needs to be and overthinking it?

 

[Nine Banger]

Since I’ve never done a grind to fit, what is the weapon of choice for the grinding? Belt sander? Disc sander? Sandpaper by hand? Or am I making this harder than it needs to be and overthinking it?

Belt sander, then finish by hand with oil/soap/water and a wet sanding block. There's a really good youtube video by one of the manufacturer's but don't over think it. I think he finishes his with Lemon Pledge or something like that; I didn't have any and life went on.

I did mine with a couple layers of blue tape on the stock figuring when the tape started to sand off it's time to quit. It only took a couple minutes to knock it out. The chatter marks you see in some of the photos above are from bouncing from pushing too hard or coming in at a steep angle so avoid that.

 

[BCsteve]

What's the best way to pop off the glued pad?

 

[Nine Banger]

What's the best way to pop off the glued pad?

Squeeze the end of the stock between your thumbs and fingers with both hands. It should pop off.

Get in the crack with a razor knife if it it doesn't just pop off.

 

[Matt5266]

I used epoxy on other stocks in the past. I didn't have any so I used Loctite 380 on these. Only less than 1/4" of grinding on the top and bottom and very little along the sides. The Pachmayr weighed almost the same as the factory pad, spacers, and screws but was a fraction of an ounce lighter before grinding
View attachment 1019063

Thank you. Looks really good

 

[Jimbee]

Are folks changing out recoil pads on rokstoks for increased LOP, or are there some other benefits?

 

[Nine Banger]

Are folks changing out recoil pads on rokstoks for increased LOP, or are there some other benefits?

LOP. I only needed 1/2" to get proper eye relief on a Maven RS1.2 with the front ring on the front most recoil pin and the erector housing of the scope almost touching that ring.

The 1" pad resolved the issue without adding a spacer kit.