RokStok

[rackcity24]

Rokscope? What have I missed?

Would you buy this scope?

Scope specs: FFP 3-12x40 to 3-12x44mm Consistently holds zero through 3-foot drops and 3,000 rounds of constant use. The reticle is specially designed for 25 to 600 yards, with bold outer posts and correct center aiming references. Zero Stop Low profile top turret. Capped windage. Large...

rokslide.com

 

[coast range]

Just ordered mine today as well.. My buddy has one and I've gotten behind it a few times and his UM low rings are always too low for me and I can never get my eye in the scope. What would be a better idea, getting the mediums or highs from UM?

I’d get a set of medium, if they don’t work, send them back for highs

 

[khuber84]

Just ordered mine today as well.. My buddy has one and I've gotten behind it a few times and his UM low rings are always too low for me and I can never get my eye in the scope. What would be a better idea, getting the mediums or highs from UM?

High Tikka direct mount rings for me. I run 1.250 rings on my rem700 rokstok as well.

 

[mxgsfmdpx]

Just ordered mine today as well.. My buddy has one and I've gotten behind it a few times and his UM low rings are always too low for me and I can never get my eye in the scope. What would be a better idea, getting the mediums or highs from UM?

You’ll probably be fine with mediums. The couple folks that I’ve seen that “need” high rings, set up on the gun fairly far back and are usually shooting from a bench not a field shot.

Can always order both and sell the other set.

 

[BearGuy]

You’ll probably be fine with mediums. The couple folks that I’ve seen that “need” high rings, set up on the gun fairly far back and are usually shooting from a bench not a field shot.

Can always order both and sell the other set.

Ordering both sounds like a good idea. I’m always looking for investors to help me with my gun builds to purchase things like 2 sets of expensive scope rings. Any interest?

 

[kopmantrey]

Really really nice. Made me remember that I have a friend that has a duplicator… Did you have to reinforce the wrist?

I imbedded a carbon fiber dowel down through grip from under the action.

 

[JCMCUBIC]

Just ordered mine today as well.. My buddy has one and I've gotten behind it a few times and his UM low rings are always too low for me and I can never get my eye in the scope. What would be a better idea, getting the mediums or highs from UM?

I initially moved a scoped barreled action from a VG to the RS. It was wearing a Mavin 1.2 in UM lows. It wasn't a good fit off hand and I was having trouble getting "down" on the scope. Ordered UM highs, mounted the scope with the same ring spacing, and they worked.

When the second RS arrived I moved an unscoped barreled action to it and only had lows to use. Using another Mavin 1.2 I mounted it a little more forward and the lows worked great. After this, I replaced the highs on the previous with UM lows and moved the scope a bit forward.

All that to say, where your cheek weld is located makes a difference in the height. Both lows and highs worked for me, just had to slide the scope forward a bit. Even the power setting of the scope plays in as one with variable eye relief like the Mavin (3.3" vs 3.9") will be a 1/2" difference.

If you want to try UM highs, send me a pm and you're welcome to try these.

 

[Speaks]

Possibly dumb question but does the rokstock not come with sling studs on it? Are you guys adding them or does no one use a rifle sling on these.

 

[Nine Banger]

Possibly dumb question but does the rokstock not come with sling studs on it? Are you guys adding them or does no one use a rifle sling on these.

My April order just came with flush cups but no sling studs. I didn't ask for the flush cups so I assumed they are standard now.