RokStok

[Randonee]

Is there a listed weight on a Rem 700 inlet yet? Have seen some Tikka weights on here. Was curious where the 700’s came in at.


Sent from my iPhone using Tapatalk

Mine is for a Medium action, pic/arca, qr studs on side, Cerakote, and bedded.
1.81#, 1lbs 13oz

 

[6.5x284]

Mine is for a Medium action, pic/arca, qr studs on side, Cerakote, and bedded.
1.81#, 1lbs 13oz

Thanks! Sendero contour?


Sent from my iPhone using Tapatalk

 

[ehayes]

? There’s nothing to deal with- it takes 20 seconds to install a new stock on average.

Is epoxy necessary for the recoil lug on the tikka Rokstok ?

 

[Randonee]

Sendero contour?

Ace #3/BM #5 contour for an Ace #2 barrel.

 

[wind gypsy]

Is epoxy necessary for the recoil lug on the tikka Rokstok ?

Mine was stuffed in there tight, so not in my case.

I'm pretty ignorant on risk mitigation/improvements/issue diagnosis/etc in relation to the tikka recoil lug situation but with factory stocks, KRG chassis, and a rokstok, it's all been a pretty simple process of sticking an action in, making sure the lug is in the slot, and tightening action screws while putting rearward pressure on the action.

Maybe a different thread about any best practices for making sure tikka recoil lugs are setup properly would be helpful? If it's just a matter of making sure it's tight in the stock and seated in the slot when action is torqued, maybe not..

 

[Castle Rock]

Is epoxy necessary for the recoil lug on the tikka Rokstok ?

As I said above, and this holds true for any stock, if it falls out when the stock is turned upside down or you can pull it out with your fingers

 

[JollyRoger]

In case anyone else is using the KRG Midas trigger group… High Desert Rifleworks just came out with a bottom metal that will accommodate it.

I’ve been using a factory bottom plastic that I filed out to fit the trigger, it works just fine but this new bottom metal should allow better fit and easier use with gloved hands. I’ll do an update once they arrive and I can try them out with my RokStok

 

[RockAndSage]

Maybe a different thread about any best practices for making sure tikka recoil lugs are setup properly would be helpful? If it's just a matter of making sure it's tight in the stock and seated in the slot when action is torqued, maybe not..

That would be helpful and appreciated for me as well. A thread about Tikka mods and Tikka smithing in general (caliber/bolt swaps, this lug thing, common challenges or known things more experienced people like to address eventually, etc).

 

[JollyRoger]

That would be helpful and appreciated for me as well. A thread about Tikka mods and Tikka smithing in general (caliber/bolt swaps, this lug thing, common challenges or known things more experienced people like to address eventually, etc).

I think the lug is being made into a bigger deal than it needs to be or actually is. Makes sure it’s seated. Then put the rifle in the stock/chassis and work it until it seats.

As for anything else you may ever need to know, the mountain tactical site and YouTube channel shows you about anything you could ever want to do with your Tikka

 

[Moose Drool]

Anymore have a Tikka CTR in a Rokstock yet? Curious what barrel profile you picked. Thanks

 

[walk2112]

Anymore have a Tikka CTR in a Rokstock yet? Curious what barrel profile you picked. Thanks

Don't have mine yet, (ordered an LE Green), but I went with Sendero/M24 inlet because I like to be able to store 1 dead cat on each side of the barrel. I can pop my CTR barreled action into the RokStok I do have though (also Sendero/M24 inlet) and post some pictures if you'd like

 

[Moose Drool]

Don't have mine yet, (ordered an LE Green), but I went with Sendero/M24 inlet because I like to be able to store 1 dead cat on each side of the barrel. I can pop my CTR barreled action into the RokStok I do have though (also Sendero/M24 inlet) and post some pictures if you'd like

Thanks. That would be awesome if you don’t mind.

 

[walk2112]

Thanks. That would be awesome if you don’t mind.

CTR in Sendero RokStok inlet:



CTR in factory stock inlet, which has been trouble free as best I can tell, even with some torquing pressure from big bipod that is cantilevered out in front of forend tip:


… and for another reference, the ‘lite’ contour in Sendero RokStok inlet:

 

[jsider]

Anyone have pics of Rem700SA?

 

[Moose Drool]

Looks good. Thanks

 

[slowelk]

@Unknown Munitions looking forward to your update after your visit to @Stockys

 

[mlevimadden]

@Unknown Munitions any chance you can touch on the LE green pattern stocks in your update?

 

[Jmedin]

Perhaps I missed this. Does the R700 short action inlet fit an Impact 737R action?

I’ve been wondering this as well. Anybody know?

 

[rbutcher1234]

I’ve been wondering this as well. Anybody know?

@Ryan Avery @Stockys @Unknown Munitions

 

[ID_Matt]

I’ve been wondering this as well. Anybody know?

Isn't an impact 737 the same inlet as a standard 700 with the exception of a trigger hanger? I don't see why it wouldn't work unless it needs some minor inletting for the hanger.